A Raft foundation shown in the figure below with the following information: all columns have the same load P - 1920 kNdimensions (0.4mx0.4m), 4-140 kPa, je 35 Mpa and f 420 Mpa. Find:1.The Foundation dimensions (L& B)2.If d-0.55m check the effective depth d by two way action (if DL. - 3LL).3. The steel Area (As) at points C & D for strip (AE).152 mL/3L/34☐L/3

Answered: Image /qna-images/answer/701439d3-08f6-4a63-bce0-ae1f5451daeb.jpg

Answered: A Raft foundation shown in the figure…

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.11P

See similar textbooks

Similar questions

A continuous foundation is required in a soil where c=10kN/m2, =26, and =19.0kN/m3. The depth of the footing will be 1.0 m. The dead load and the live load are 600 kN/m and 400 kN/m, respectively. Determine the required width for the foundation based on allowable stress design with FS = 3, using Eq. (6.10) and Table 6.1.
For the mat in Problem 16.15, what will be the depth, Df, of the mat for FS = 3 against bearing capacity failure? 16.15 Consider a mat foundation with dimensions of 18 m 12 m. The combined dead and live load on the mat is 44.5 MN. The mat is to be placed on a clay with cu = 40.7 kN/m2 and = 17.6 kN/m3. Find the depth, Df, of the mat for a fully compensated foundation.
Repeat Problem 11.1 based on LRFD using the following factors: load factor for dead load = 1.25 load factor for live load = 1.75 strength reduction factor on the ultimate bearing capacity = 0.50 11.1 A continuous foundation is required in a soil where , , and . The depth of the footing will be 1.0 m. The dead load and the live load are 600 kN/m and 400 kN/m, respectively. Determine the required width for the foundation based on allowable stress design with FS = 3, using Eq. (6.10) and Table 6.1.
A 2.0 m wide strip foundation is placed in sand at 1.0 m depth. The properties of the sand are: = 19.5 kN/m3, c = 0 and =34. Determine the maximum wall load that the foundation can carry, with a factor of safety of 3.0, using a. Terzaghis original bearing capacity equation with his bearing capacity factors b. Meyerhofs modified bearing capacity equation with appropriate factors (Tables 16.2 and 16.3).
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
A flexible circular footing of radius R carries a uniform pressure q. Find the depth (in terms of R) at which the vertical stress below the center is 20% of q.
Consider a continuous foundation of width B = 1.4 m on a sand deposit with c = 0, = 38, and = 17.5 kN/m3. The foundation is subjected to an eccentrically inclined load (see Figure 6.33). Given: load eccentricity e = 0.15 m, Df = 1 m, and load inclination = 18. Estimate the failure load Qu(ei) per unit length of the foundation a. for a partially compensated type of loading [Eq. (6.89)] b. for a reinforced type of loading [Eq. (6.90)]
Repeat Problem 20.2 based on LRFD using the following factors. Load factor for dead load = 1.25 Load factor for live load = 1.75 Strength reduction factor on the ultimate bearing capacity = 0.50 20.2 A continuous foundation is required in a soil where c = 10 kN/m2, =26 and = 19.0 kN/m3. The depth of the foundation will be 1.0 m. The dead load and the live load are 600 kN/m and 400 kN/m, respectively. Determine the required width for the foundation based on allowable stress design with FS = 3, using Eq. (16.3) and Table 16.1.
Redo Problem 7.6 using Vesic’s (1975) solution [Eq. (7.12)]. 7.6 A 2.0 m wide continuous foundation is placed at 1.5 m depth in a saturated clay where cu = 40 kN/m2 and γ = 18.5 kN/m3. At 2.0 m below the ground level, this clay layer is underlain by a stiffer clay where cu = 60 kN/m2 and γ = 19.0 kN/m3. What would be the maximum wall load allowed with FS = 3? Use Eq. (7.11).
In Problem 7.1, if there was no bedrock present for at least 12.0 ft below the foundation, what would the ultimate bearing capacity be? 7.1 A 7.5 ft wide rough continuous foundation is placed in the ground at 3.0 ft depth. There is bedrock present at 3 ft depth below the bottom of the foundation. The soil properties are c′ = 210 lb/ft2, ϕ′ = 25°, and γ = 115.0 lb/ft3. Determine the ultimate bearing capacity of the foundation.
A square foundation is shown in Figure P6.19. Use FS = 6, and determine the size of the foundation. Use Prakash and Saran’s method [Eq. (6.59)]. Figure P6.19
Determine the maximum column load that can be applied on a 1.5 m × 1.5 m square foundation placed at a depth of 1.0 m within a soil, where γ = 19.0 kN/m3, c′ = 10 kN/m2, and ф′ = 24°. Allow a factor of safety of 3.0.

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781305081550

Author:

Braja M. Das

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Geotechnical Engineering (MindTap…

Civil Engineering

ISBN:

9781305635180

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781305081550

Author:

Braja M. Das

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Geotechnical Engineering (MindTap…

Civil Engineering

ISBN:

9781305635180

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Principles of Geotechnical Engineering (MindTap C…

Civil Engineering

ISBN:

9781305970939

Author:

Braja M. Das, Khaled Sobhan

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS