A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t= 0.1250 in. The average shear stress in the pin cannot exceed 30 ksi, and the bearing stress in the pulley support bracket cannot exceed 70 ksi. Determine the maximum value of Pmax that can be supported by the assembly.

A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t= 0.1250 in. The average shear stress in the pin cannot exceed 30 ksi, and the bearing stress in the pulley support bracket cannot exceed 70 ksi. Determine the maximum value of Pmax that can be supported by the assembly.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4- A hollow tubular shaft is 1.5 m long and has an outer diameter of 75-mm. The shaft transmits the power of 30 kW from the motor E to the generator G when it rotates at 500 rpm. Determine the smallest thickness of the tube if the allowable shear stress is 123 MPa. E
2. Two elastic bars are connected and supported as shown. The thermal load is a 10°C temperature increase and the mechanical load is a 5 kN rightward force where the bars are connected to each other. Determine the stress in each bar and the displacement of the connection point. Brass Steel E = 200 GPa a= 12(106)/C Ag = 200 mm Err = 100 GPa - 21(10 )/°C Abr = 450 mm? 300 mm 300 mm
The drive shaft of a car is designed to be a tube with an outer diameter of 4 in. The engine delivers 190 hp when the shaft is turning at 1200 rpm. The material of the drive shaft has a allowable shear stress of Tallow = 8 ksi. T = a. Determine the magnitude of torque in the shaft, T. b. Determine the minimum required wall thickness of the shaft,t. lbin t = in
For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the load is P = 64 kips.
The rigid wrench (not the brand Rigid sold at Home Depot!) shown is used to loosen a stuck nut at the top of a 4 mm radius smooth shafted bolt that is fixed supported at the base A. Determine the largest force F that can be applied if the bolt has a maximum shear stress of for this maximum torque value. G=75 GPa 18 MPa. Also determine the distance each force will move Ans: 6.03 N F. 150 mm 150 mm 80 mm
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 14 mm and an allowable normal stress of 135 MPa. Pipe (2) has an outside diameter of 56 mm, a wall thickness of 6 mm, and an allowable normal stress of 160 MPa. Assume x₁ = 3.6 m, x₂ = 2.4 m, and y₁ = 3.0 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. B P Y₁ Answer: Pmax i (2) C KN
Provide a complete, step by step solution:
The solid circular rod has a cross-sectional area of 350 mm². It is subjected to a uniform axial distributed loading along its length of w = 5 kN/m. Two concentrated loads also act on the rod: P = 5 kN and Q = 6 kN. Determine the normal stress in the rod at x = 1.1 m. Assume a = 0.5 m and b = 1.4 m. W A B MPa >x a Answer: 0 = i b
The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear stress in the bolts must be limited to 185 MPa, determine the minimum bolt diameter that may be used in the connection. P 24.3 mm O 18.5 mm O 22.6 mm 29.3 mm O 14.0 mm
Two solid cylindrical rods support a load of P = 32 kN as shown. Rod (1) has a diameter of 14 mm, and the diameter of rod (2) is 12 mm. Determine the axial stress in rod (1). 3.8 m 4.6 m (1) 5.6 m O 169.0 MPa 139.6 MPa 125.8 MPa O 104.5 MPa O 182.6 MPa B U 3.3 m
A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t= 0.1250 in. The average shear stress in the pin cannot exceed 40 ksi, and the bearing stress in the pulley support bracket cannot exceed 70 ksi. Determine the maximum value of Pmax that can be supported by the assembly. Pulley support bracket Answer: Pmax i ! kips %3D
The bell-crank mechanism is in equilibrium for an applied load of F₁ = 18 kN applied at A. Assume a = 290mm, b = 170mm, c = 70mm, and 0 = 35°. Pin B is in a double-shear connection and has a diameter of 23 mm. The bell crank has a thickness of 37 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Support bracket Answers: Tpin 8 = i Bell crank i a B MPa MPa F₂