The bell-crank mechanism is in equilibrium for an applied load of F₁ = 13 kN applied at A. Assume a = 300mm, b = 140mm, c= 85mm and 0 = 45°. Pin B is in a double-shear connection and has a diameter of 34 mm. The bell crank has a thickness of 25 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Bell crank F₂ Support bracket A Answers: Tpin B = i Ob = i a B b MPa MPa

The bell-crank mechanism is in equilibrium for an applied load of F₁ = 13 kN applied at A. Assume a = 300mm, b = 140mm, c= 85mm and 0 = 45°. Pin B is in a double-shear connection and has a diameter of 34 mm. The bell crank has a thickness of 25 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Bell crank F₂ Support bracket A Answers: Tpin B = i Ob = i a B b MPa MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bell-crank mechanism is in equilibrium for an applied load of F₁ = 12 kN applied at A. Assume a = 250mm, b = 170mm, c = 80mm, and 0 = 50°. Pin B is in a double-shear connection and has a diameter of 20 mm. The bell crank has a thickness of 25 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Support bracket A Answers: Tpin B = i Ob= i Bell crank a B b MPa MPa
The d = 14-mm-diameter solid rod passes through a D = 19-mm-diameter hole in the support plate. When a load Pis applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 11 mm. The rod head has a diameter of a = 28 mm, and the head has a thickness of t = 8 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 95 MPa, and the bearing stress between the rod head and the support plate cannot exceed 125 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate - Hole diameter D Rod Нead b -
Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 2.5 kN. The crankshaft dimensions are b1 = 80 mm, b2 = 135 mm, and b3 = 55 mm. The diameter of the upper shaft is d = 26 mm. Determine the normal stress at point B, which is located on the surface of the upper shaft at the yo axis. Yo Хо b3 Lütfen birini seçin: a. 149.606 MPa b. 324.676 MPa c. 139.544 MPa d. None e. 190.884 MPa
The assembly is used to support a distributed loading of w = 6.6 kN/m. The solid steel rod BC has a diameter of 13 mm and the steel pins at A, B and C have a diameter of 10 mm. The yield stress of the steel in tension is 250 MPa and in shear is 125 MPa. C 1.2 m 0.9 m 0.3 m Determine the factor of safety for the pin at B with respect to yielding? Input your answer to two decimal places.
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 175 MPa. Pipe (2) has an outside diameter of 52 mm, a wall thickness of 8 mm, and an allowable normal stress of 175 MPa. Assume x1 = 2.9 m, x2 = 1.4 m, and y1 = 3.8 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. B (1) C Answer: Pmax i kN
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 33 kips, F₂ = 18 kips, F3 = 25 kips, and F4 = 38 kips, determine the absolute value of the axial load in rod (2). F₁ A F₂ (1) F₂ B F3 (3) F3 F₁ с D O 21 kips 16 kips 29 kips 25 kips O 19 kips
The five-bolt connection must support an applied load of P = 1800 lb. If the average shear stress in the bolts must be limited to 47 ksi, determine the minimum bolt diameter that may be used for this connection.
The stresses shown on the right below act at a point on the surface of a cantilever beam, as shown on the left. Determine the normal and shear stresses at this point on the inclined plane A-B, by drawing a suitable free-body diagram and applying the equations of force equilibrium. A √70° B 5 ksi -20 ksi
An axial force of 52 kN is applied to the assembly shown by means of rigid end plates. 5 mm 5 mm 20 mm 20 mm 5 mm 5 mm Steel core E = 200 GPa Brass shell E = 105 GPa 250 mm Determine the normal stress in the brass shell. The normal stress in the brass shell is MPа.
The bolt AB in (Figure 1) has a diameter of 18 mm and passes through a sleeve that has an inner diameter of 42 mm and an outer diameter of 52 mm. The bolt and sleeve are made of A-36 steel and are secured to the rigid brackets as shown. If the bolt length is 220 mm and the sleeve length is 200 mm, determine the tension in the bolt when a force of 50 kN is applied to the brackets.
Three metal rods are firmly attached to the walls and the middle rigid plate. Rod AB is made from stainless steel and rods CD and EF are made from 2014-T6 aluminum. If a balanced load is applied to the rigid plate, determine what the stresses are in the rods. Follow the sign convention that tensile stress is positive and compressive stress is negative. The parameter values are listed in the table above the figure. parameter value units L. 450 mm L2 300 mm d₁ 40 mm d2 30 mm P 40 KN L1 d₁ P B CC 030 BY NO SA 2021 Cathy Zupke P L2 D U MPa MPa The stress in AB σAB= The stress in CD and EF: σCD = σEF= E F
The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 10 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t = 8 mm. The shear stress in the rod head cannot exceed 145 MPa, the punching shear stress in the support plate cannot exceed 100 MPa, and the bearing stress between the rod head and the support plate cannot exceed 145 MPa. Determine the maximum value of Pmax that can be supported by the structure.