The stresses shown on the right below act at a point on the surface of a cantilever beam, as shown on the left. Determine the normal and shear stresses at this point on the inclined plane A-B, by drawing a suitable free-body diagram and applying the equations of force equilibrium.

The stresses shown on the right below act at a point on the surface of a cantilever beam, as shown on the left. Determine the normal and shear stresses at this point on the inclined plane A-B, by drawing a suitable free-body diagram and applying the equations of force equilibrium.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A circular bracket with a diameter of 100 mm is fixed to a wall as shown in the figure below. Determine and draw the state of stresses in small infinitesimal cubic elements located at pooints M and N on the cross section A.
Figure shows a beam made from bronze subjected to a 3.5kN.m bending couple and its respective tensile properties. i) With aid of illustration, draw the deformation of the bean and locate the position where the beam experience maximum tensile stress (αmax)t and maximum compressive stress (αmax)c. Accordingly. Determine the magnitude of these two stresses. ii) Sketch the two-dimensional stress distribution acting on point A and point B over the cross-sectional area of the beam as observed from side view. Estimate the magnitude of the stresses at those two points.
Let’s consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a material having a Young’s modulus E = 200 Gpa and a Poisson’s ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 5.998 mm. determine the applied force F.
.An element in the boiler is triaxially stressed, the stresses distribution is given by (see Figure 1). Oxx = 75 MPa; on = 60 MPa; 0 = 50 MPa; Try = 25 MPa; tyz = - 25 MPa; ta = 0 MPa. determine the components of this stress state on a x'y' z' coordinate axes system described by the following direction cosines. y 2/3 -2/3 -1/3 2/3 1/3 2/3 -1/3 -2/3 2/3 y' Compute also the magnitudes and directions of the principal stresses. 60 MPa 25 MPа 75 MPa 50 MPa 25 MPа Figure 1
To use the superposition principle to find the state of stress on a beam under multiple loadings. The beam shown below is subjected to a horizontal force P via the rope wound around the pulley. The state of stress at point A is to be determined. P D di 20 mm 100 mm 200 mm 15 mm 20 mm 150 mm T The dimensions are di = 1.9 m, d2 = 0.7 m, d3 = 1 m, da = 355 mm, and r = 230 mm. The applied force has magnitude P =6 kN.
4- The cross-section of the ABCD element in the figure is a circle with a diameter of 6 cm. The force of P-500 N is in the x-z plane. The CD segment is parallel to the y-axis. In line with the information given, a- Find the most critical points in section A. b- Calculate the normal and shear stresses at the most critical points in section A. c- Calculate the principal stresses at the specified points. d- Check the section with the Tresca Hypothesis. em = 95 MPa 75 cm B A N 50 cm 10 40 cm P
The cantilever beam with a rectangular cross-section is under the loading P as shown in the figure. P Part A At an arbitrary cross-section, a - a the state of stress is obtained at various points (point 1 - 5, where point 3 is the midpoint). Select all that describe the stress at the cross-section a - a correctly. O The cross-section a-a has three internal loadings, i.e., shear force, normal force, and bending moment. O The normal stress by bending moment at point 5 is zero. O The maximum shear stress by shear force occurs at the same point as the maximum normal stress by bending moment. O The maximum shear stress by shear force occurs at point 3. O Point 1 develops compressive normal stress by bending moment. O The shear stress by shear force at point 1 is zero. Submit Request Answer
This is Mechanical Engineering. Please answer with clear work and answers. Thank you
Figure Q5 shows a thick cylinder of 50 mm internal radius and 130 mm outer radius is subjected to an internal pressure of 60 MN/m2 and an external pressure of 30 MN/m2. Determine the hoop and radial stresses at the inside and outside of the cylinder together with the longitudinal stress if the cylinder is assumed to have closed ends using analytical and graphical approaches
I need it handwritten and correct or skip please only handwritten handwritten handwritten handwritten otherwise dislikfor sure
(1) In the figure below, the cross section areas of rods AB and BC are A1, A2, and the Young's moduli are E1 and E2, respectively. For loads P1 and P2 applied as shown in the figure, (a) determine the normal stresses in rods AB and BC; (b) determine the deformation at C. D L1/2 A B C P1 P2 Li L2 A1, E1 A2, E2
A bar of square cross-section is subjected to point loads of P1, P2, P3, and P4 as shown here. Find the magnitude of the force P3 necessary for the equilibrium, if P1= 130 kN, P2 = 230 kN & P4 = 180 kN. Also, determine the stresses in each section & the net change in the length of steel bar, where the respective side of a square and lengths are d1=55mm, L1=31 cm, d2 = 40mm, L2=38 cm, d3=55 mm & L3 =30 cm. Take E = 185 GPa. The force P3 to make it to equilibrium in kN is The Stress in section 1 in N/mm2 is The Stress in section 2 in N/mm2 is The Stress in section 3 in N/mm2 is and The total change in length in x10-3 mm is