The d = 14-mm-diameter solid rod passes through a D = 19-mm-diameter hole in the support plate. When a load Pis applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 11 mm. The rod head has a diameter of a = 28 mm, and the head has a thickness of t = 8 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 95 MPa, and the bearing stress between the rod head and the support plate cannot exceed 125 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate Hole diameter D d Rod Нad b -

The d = 14-mm-diameter solid rod passes through a D = 19-mm-diameter hole in the support plate. When a load Pis applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 11 mm. The rod head has a diameter of a = 28 mm, and the head has a thickness of t = 8 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 95 MPa, and the bearing stress between the rod head and the support plate cannot exceed 125 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate Hole diameter D d Rod Нad b -

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q-63: At a point, the stress components are: 0x = 600 dy = 300 Txy = 500 Tyz = 400 %₂ = 900 Txz = -200 kpa Show that the principal directions of stress and deviative stress coincide.
Please help me answer this asap thank you
The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial distributed loading along its length of w= 8 kN/m. Two concentrated loads also act on the rod: P = 3 kN and Q = 5 kN. Determine the normal stress in the rod at x = 0.9 m. Assume a = 0.6 m and b = 1.0 m. B MPa a Answer: 0 = i b
pls help
The bell-crank mechanism is in equilibrium for an applied load of P = 47 kN. Assume that a = 300 mm, b = 225 mm, and 0 = 57°. The pin at B has a diameter of d = 14 mm, and the bell crank has a thickness of t = 8 mm. Calculate the bearing stress in the bell crank at pin B. (1) P Answer: Bell crank A O= i 34.21 a с MPa B Support bracket b F₁ IF B
25 kN 25 KN 12 mm 18 mm 1.55 The lap joint is fastened with four 3/4-in.-diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. 7.5 mm 25 KN 7.5 mm 4 in. in. 25 KN 12 mm 12.5 mm FIG. P1.54 18 mm 78 in. FIG. P1.55 78
An axial force of 52 kN is applied to the assembly shown by means of rigid end plates. 5 mm 5 mm 20 mm 20 mm 5 mm 5 mm Steel core E = 200 GPa Brass shell E = 105 GPa 250 mm Determine the normal stress in the brass shell. The normal stress in the brass shell is MPа.
number 9
Only do the safety factor part
The bell-crank mechanism is in equilibrium for an applied load of F1 = 17 kN applied at A. Assume a = 290mm, b = 120mm, c = 80mm, and e = 35°. Pin B is in a double-shear connection and has a diameter of 33 mm. The bell crank has a thickness of 36 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Bell crank F2 Support bracket A a Answers: Tpin B = MPa Ob = i MPa
Assemble a pair of parts A and B with serrated teeth as shown in the figure on the right.A compressive load of 24 kN is acting on the combined structure.The compressive load is transmitted by the three meshing teethTo. Shear stress and compressive stress (contact) generated in the tooth at this timeFind each tactile stress.
Can someone please explain the step-by-step process of this. Thank you so much! The d = 12-mm-diameter solid rod passes through a D = 17-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 13 mm. The rod head has a diameter of a = 24 mm, and the head has a thickness of t = 9 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 85 MPa, and the bearing stress between the rod head and the support plate cannot exceed 130 MPa. Determine the maximum value of Pmax that can be supported by the structure.