A pressurizer is simplified as a cylindrical pressure containerwith a diameter D = 5 m. The pressurizer contains waterwith height H = 10 m under normal operation. The pressurein the top of the water level is 15 MPa under normaloperation. Under the following system abnormalities,determine the level of water in the pressurizer tank?1. when the pressure was raised to 20 MPa.2. When the pressure was lowered to 10 MPa.D = 5 mH = 10 m

Problem OverviewWe have a cylindrical pressurizer that contains water, and we need to determine how…

Answered: A pressurizer is simplified as a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer question three part two
Because of a break in a buried oil storage tank, ground water has leaked into the tank to the depth L' = 3 ft. The densities of the water and oil are, respectively, 62 and 55, each in lb/ft³. * Your answer is incorrect. P₂(gage) = i Determine the pressure at the oil-water interface and at the bottom of the tank, each in lbf/in². (gage). Assume L = 17 ft. Let g = 32.2 ft/s². Standpipe open to atmosphere 17.432 * Your answer is incorrect. Determine the pressure at the oil-water interface, in lbf/in². (gage). Pb(gage) = i Pam Oil lbf/in². Water Determine the pressure at the bottom of the tank, in lbf/in². (gage). lbf/in².
Three types of fluids stack in an open tank as shown in the plot. Select the expression of the gage pressure at location 3, P3(gage)=______ A. B. C. D.
SG of Water=1.0 SG of Mercury=13.6 SG of n-Octane=0.65
Answer the following questions with solution/ detailed explanation: 1. The pressure in an automobile tire depends on the temperature of the air in the tire. When the air temperature is 25°C, the pressure gage reads 210 kPa. If the volume of the tire is 0.025 m3, determine the pressure rise in the tire when the air temperature in the tire rises to 50°C. Also, determine the amount of air that must be bled off to restore pressure to its original value at this temperature. Assume the atmospheric pressure to be 100 kPa.
1. Oxygen at 30°C and 300 kPa absolute pressure expands isotherrnally to an absolute pressure of 120 kPa. Determine the final density of the gas. Ans. 1.52 kg/m³ 2. Air is enclosed by a rigid cylinder containing a piston. A pressure gage attached to the cylinder indicates an initial reading of 25 psi. Determine the reading on the gage when the piston has compressed the air to one-third its original volume. Assume the compression process to be isothermal and the local atmospheric pressure to be 14.7 psi. Ans. 104 psig 3. The viscosity of liquids can be measured through the use of a rotating cylinder viscometer of the type illustrated in Fig. P1.3. In this device the outer cylinder is fixed and the inner cylinder is rotated with an angular velocity w. The torque T, required to develop w is measured and the viscosity is calculated from these two measurements. Develop an equation relating u, w, T, e, Ro and Ri. Neglect end effects and assume the velocity distribution in the gap is linear.…
I need the answer as soon as possible
A pressure gage connected to a tank reads 450 kPa at a location where the atmospheric pressure is 94 kPa. Determine the absolute pressure in the tank. The absolute pressure in the tank is ______ kPa.
Problem 1: A certain rigid aluminum container contains a liquid at a gauge pressure of P0 = 2.02 × 105 Pa at sea level where the atmospheric pressure is Pa = 1.01 × 105 Pa. The volume of the container is V0 = 2.15 × 10-4 m3. The maximum difference between the pressure inside and outside that this particular container can withstand before bursting or imploding is ΔPmax = 2.41 × 105 Pa.For this problem, assume that the density of air maintains a constant value of ρa = 1.20 kg / m3 and that the density of seawater maintains a constant value of ρs = 1025 kg / m3. Part (a) The container is taken from sea level, where the pressure of air is Pa = 1.01 × 105 Pa, to a higher altitude. What is the maximum height h in meters above the ground that the container can be lifted before bursting? Neglect the changes in temperature and acceleration due to gravity with altitude. Part (c) Choose the correct answer from the following options. The depth below the surface of the ocean…
Q2:- Note: 1 Torr = 0.133 kPa & 1 atm 101.325 kPa (A) A spray metal bottle is used for polishing some Aluminum samples until it is empty. Then, the rest propellant gas inside the bottle has a pressure of 1344 torr at 23 °C. Finally, if the spray bottle is thrown into a fire at a temperature equals 475 °C. Determine the pressure in the hot bottle in kPa? Assuming no change in volume.
Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading on the pressure gage is 100 kPa, determine the distance between the two fluid levels of the manometer if the fluid is
Q 10: An inverted tube differential manometer having an oil of specific gravity 0.9 is connected to two different pipes carrying water under pressure. Determine the pressure in the pipe B. The pressure in pipe A is 2 m of water. [Ans: h= 1.88 m, p = 18.44 kN/m2]

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS