TtTxy2.1The stresses of a gear shaft at the position of the maximumload (=boundary fibre at the point of the maximum bending stress) arecalculated to σ = 60 N/mm² and ɩ = 40 N/mm². Determine theextreme values of normal and shear stress (σmax; ☛min; || max) and theirorientation (=angle to the σb-axes) with the help of Mohr's Circle. What are the stresses σx*; σy*; Txy*at an angle of a = 45° to the σ−axes? Check the results using the formulars! What are the equivalentstresses oeqN (Tensile Stress Hypothesis), eqs (Shear Stress Hypothesis), GeqM (van Mises Criterion)?

Answered: Image /qna-images/answer/324379f4-f8b9-44e1-83a7-b39750cd70c3.jpg

Answered: Tt Txy 2.1 The stresses of a gear shaft…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I am struggling with this question
A state of stress at a point A is given by σx = 45 MPa, σy = 9.1 MPa, and τxy = -5.75 MPa. What is the maximum in-plane shear stress for the point A.
The state of stress in a body is uniform and is given by: 0xx = 3MPa; Txy = 2 MPa; Txz = 4MPa Oyy = 5MPa; Tyz = OMPa; ozz 2MPa = a. Determine the principal stresses and their corresponding eigenvectors (work must be performed by hand) b. Determine the stress vector on a plane oriented at nx=.707, ny=.707, n₂=0 c. Determine the normal stress on the plane given in item (b)
The shaft CD is affected by a torque T = 1000 Nm as shown. The shaft diameters are DAB = 53 mm and DCD = 43 mm. Determine the maximum shear stress due to torque in the AB axis. Use units [N, mm] Enter the answer to one decimal place. Do not round the invoices in the intermediate stages, but only the final answer!
The copper pipe [G = 7,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 80 lb-ft/ft along its entire length. Using a = 2.5 ft, b = 4.0 ft, and c = 8.5 ft, determine(a) the maximum shear stress in the pipe.(b) the rotation angle φC at the free end of the shaft.
I have been stuck on this problem for while thar area is 779.1 mm^2 sigma_x is 120.6497159 sigma_y is 0 and tau_xy is 0. Beta is 20 degrees
A hollow shaft has to transmit 6MW at 150rev / min. The maximum allowable stress is not to exceed 60 MN / m? nor the angle of twist 0.3 ° per meter length of shafting. If the outside diameter of the shaft is 300 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN / m?
Mechanics of deformable bodies
For the shaft shown below, determine the normal and shear stresses acting on the element located at point A, including stress concentrations. Then draw the stress element at A with the applied stresses and determine the three principal stress (0₁, 2 and, σ3) using Mohr's circle. r = 0.0042 m, d = 0.03 m, D = 0.033 m, T = 250 Nm P = 1500 N, M = 300 Nm, A M M DEHRƏC T d T P P r
Q2\ Determine the torsional stress of the cantilever shafts show in the figures below. 86= b T 5 KN.m T 200 5 KN.m 20 0 20 0 Note: All dimensions in mm. ·2=15 70 200 Note: All dimensions in mm. 15 0,
A circular shaft of 40 mm diameter is required to transmit torque from one shaft to another. Find the safe torque, which the shaft can transmit if the shear stress is not to exceed 32Mpa. 1. 2.56 π x 105 N-mm 2. 0.75 π x 105 N-mm 3. 1.28 π x 105 N-mm 4. 2.25 π x 105 N-mm X
Determine the limiting peripheral velocity of a steel ring if the allowable stress is 20 ksi the steel weighs 490lbm /ft^3 . What is the resulting stress if the ring rotates at 6500rpm ? Use r = 10in

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS