a Ports of the 8051 Microcontroller are characterized as All require pull-up resistors between port and load One requires pull-up resistors between port and load All ports are Input ports ONLY dynamic b. C. d. None of the above BAS C.

a Ports of the 8051 Microcontroller are characterized as All require pull-up resistors between port and load One requires pull-up resistors between port and load All ports are Input ports ONLY dynamic b. C. d. None of the above BAS C.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Precharge and Evaluate are two phases in: a. Dynamic CMOS logic b. Static NMOS logic c. NMOS logic d. pseudo NMOS logic
Figure on the right shows the Moore model state diagram of a synchronous sequential circuit having two inputs (x and y) and one output (Z). a) Draw the state table of the synchronous sequential circuit, b) Derive the next state equations and the equation for the output. c) If you are to use either R-S or J-K flip flop as memory elements, derive the respective inputs. 00 11 01/0 01. 11 01 11 00 00/0 -011 11/1 00 10- 00 11- 10 xy 10/0 01
Binary Counters Objective: Design, construct, and test a three-bit counter that counts up or down. A disable input D determines whether the counter is on or off. • If D=1, the counter is disabled and remains at its present count even thoughclock pulses are applied to the flip-flops. • If D-0, the counter is enabled and a second input, x, determines the directionof the count. • If x=1, the circuit counts the sequence 00, 01, 10,11 and the count repeats. • If x=0, the circuit counts the sequence 11, 10, 01, 00 and the count repeats. (Do not use D to disable the Clock) Note: Design the sequential circuit with D and x as inputs. Submission: Reports must include all schematics and cost of design. Compare your results with other solutions. (Costs, design....). Define why your design is better.
A synchronous state machine has two inputs (X1 and X2) and one output (Z). The relationship between the inputs and output is described in the following waveforms. The designer needs for . . NOT-gates for .......... implementing the circuit of the aforementioned state machine. * X1 X2 N.
• Design a sequential circuit with two T Flip Flops, A and B, and two inputs, E and x. If E=0, the circuit remains in the same state regardless of the value of x. When E=1 and x=1, the circuit goes through the state transitions from 00 to 01 to 10 to 11 back to 00, and repeats. When E=1 and x=0, the circuit goes through the state transition from 00 to 11 to 10 to 01 back to 00, and repeats
Construct a logic circuit on the ROM that produces the outputs given in the table below by comparing the two bits and two magnitudes applied to its input. Show the design clearly (ROM sizes, ROM data table).
2. Design a combinational circuit with three inputs, x, y, and z, and three outputs, A, B, and C. When the binary input represents any of the decimal digits 1, 2, 3, or 6, the binary output should represent the decimal digit that is one greater than the input, that is 2, 3, 4 and 7, respectively. Similarly, when the binary input represents any of the digits 4, or 7, the binary output should represent the digit that is two less than the input. The remaining two inputs, that are the binary representations of the decimal digits 0 and 5 never occur. Draw the truth table, and give all the minimal forms for the functions that represent the outputs A, B, and C. U
In a bridge rectifier, four diodes conduct during each half cycle of the input. O true O False
12) The two input instructions linked to input field devices for ladder logic are -- (-11-) and ------- instruction symbol (-//-). a. XIO, OTE b. XIO, XIC c. XIC, OTL d. XIC, XIO instruction sym
Draw the circuit of 2 bit universal register Selection line action SI SO 0. Shift left Parallel load Shift rignt No change (hold data) 1
3- Draw the PLC ladder logic of the following: X = ((A · B · C) + B) · B · (A + Ĉ) %3D