A member is subjected to the loads shown in Figure 3. The loads are 30% dead load and 70% live load. K = Ky = 1.0. Use A992 steel and select a W12 shape (the lightest option). Hints: The amplification factor B₁ can be estimated as 1.0 for choosing a trial selection. Then when calculating the actual B₁, use Cm = 1.0 (transversely-loaded member). 60 k

A member is subjected to the loads shown in Figure 3. The loads are 30% dead load and 70% live load. K = Ky = 1.0. Use A992 steel and select a W12 shape (the lightest option). Hints: The amplification factor B₁ can be estimated as 1.0 for choosing a trial selection. Then when calculating the actual B₁, use Cm = 1.0 (transversely-loaded member). 60 k

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

determine: (a) the elastic section modulus and the yield moment. (b) the plastic section modulus and the plastic moment Mp. Bending is about the x-axis, and the steel is A572 Grade 50. Fy = 345 MPa Subject: Civil Engineering Steel Design
The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between the jaws. In this case; a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shown in the figure. b) Show the distribution of normal stresses across the section height. (draw) c) Since the clamp material has tensile strength (apull) safety = 50MPA and compression safe stress (opress) safety = 80MPA, what is the great compressive load (P) that can be applied without damaging the a-a section? %3D %3D (Please solve in detail and according to engineering rules.) Material mechanics Sectional view a-a - 20mm T. 183mm 40mm
The rigid frame shown in Figure is unbraced. The members are oriented so that bending is about the strong axis. Support conditions in the direction perpendicular to the plane of the frame are such that Ky = 1.0. The beams are W18 x 50, and the columns are W12 x 72. A992 steel is used. The axial compressive dead load is 50 kips, and the axial compressive live load is 150 kips. a. Determine the axial compressive design strength of column AB. Use the stiffness reduction factor if applicable. b. Determine the allowable axial compressive strength of column AB. Use the stiffness reduction factor if applicable.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
Getting measurements from Figure , determine approximate values of the following items for steel with different carbon contents. Use one system of units only as specified by the instructor.a. Yield stressb. Ultimate strengthc. Strain at failured. Effect on modulus of elasticitye. Approximate toughness. Curves may be approximated with a series of straight lines.f. Comment on the effect of increasing carbon content on items a through e above.
Problem2. The compression member is shown in figure. Find the following: a. The Euler stress Fe. b. The buckling stress Fcr c. The design strength d. The allowable strength e. Does the member satisfactorily meet the design requirements? Why? HSS 8x 8x4 ASTM AS00, Grade B steel (Fy = 46 ksi) 15'
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
Two steel plates are connected by a pair of splice plates with eight bolts as shown. The ultimate strength of the bolts is bolts is 270 MPa. An axial tension load of P = 480 kN is transmitted by the steel plates. If a factor of safety of 1.6 with respect to failure by fracture is specified, determine the minimum acceptable diameter "d" for the bolts. %3D P. splice plate steel steel plate plate (2) (1)
The solid rod has a diameter of 20mm. Find the following: Angle of twist at C with respect to A (in radians) Angle of twist at B with respect to A (in radians) Maximum shear stress at A (in MPa) (Shear stress at support, at a point 7mm from center. (in MPa) A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
b. Discuss how the figure below and determine the rigid bar BDE as used to support by two link AB and CD. 0.4 m 0.3 m B D 0.4 m 30 kN E 0.2 m The Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm2. Link CD is made of steel (E = 200 GPa) and has a cross- sectional area of (600 mm2). For the 30-kN force shown, determine the deflection a) of B, b) of D, and c) of E.
When designing a structural member, which of the following statements is FALSE? A. The allowable stress is used in calculating the maximum load to be applied. B. The ultimate stress depends on the Factor of Safety used. C. The ultimate stress is determined based on the material used. D. The allowable stress depends on how conservative the design is. Which of the following is NOT a valid reason for increasing the Factor of Safety? A. Higher uncertainty in loading conditions B. Higher design life C. Lower confidence in assumed/stated material properties D. Lower member importance Consider a 1,000-mm long, 25-mm diameter sample subjected to a tension test. Automatic high-precision gages recorded that for an applied load of 150 kN, the sample experienced a longitudinal strain of 2×10−3mm/mm. Assuming that the material remained elastic while loaded, determine its modulus of elasticity. A. 175.0 GPa B. 63.7 GPa C. 152.8 GPa D. 72.9 GPa
The aluminum W 310 x 202 (wide flange) column is subjected to an eccentric axial load P as shown. The maximum compressive stress in the column is given by the so-called secant formula: where --- [¹ + ( √5)] ec o 1+ sec max E ō = P/A = average stress A = 25800 mm² = cross-sectional area of the column e = 85 mm = eccentricity of the load c = 170 mm = half depth of the column r = 142 mm = radius of gyration of the cross section L = 7100 mm = length of the column E = 71 x 10⁹ Pa = modulus of elasticity Determine the maximum load P that the column can carry if the maximum stress is not to exceed 120 × 10^6 Pa. Terminate the computation when Σa < 0.0005%.