A liquid having a sp.gr. of 20 is flowing in a 50 mm diameter pipe. The total head at a given point was found to be 17.5 Joule per Newton. The elevation of the pipe above the datum is 3 m and the pressure in the pipe is 65.6 kPa. Compute the velocity of flow and the horsepower in the stream at that point. Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow

Q: Question 1: The diagram shows water leaving a tank through an inverted V-tube. (All answers to be…

A:

Q: Q3: calculate the total residual flow using the following data Static pressure: 55 psi Residual…

A: Write the measured residual pressure. Pr=41 psi Write the desired residual pressure. Pd=20 psi Write…

Q: The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The…

A:

Q: The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The…

A:

Q: If the diameter at section 1 is D₁ = 0.5 m, and at section 2 the diameter D₂ = 0.2 m. All the other…

A:

Q: the velocity of a liquid is 1.65 ft/s in a special pipe with an inside diameter of 12 in, what is…

A: Given:v1=1.65 ft/sd1=12 ind2=3 in

Q: At high flow rates the pressure drop increases directly with fluid velocity. TRUE OR FALSE Fluid’s…

A: Note: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: A simple rainwater collector used for home garden use is show below. It is comprised of an open-air…

A: Given:- X=2m Y=3m l=4m g=9.81 m/sec2

Q: QI/b) A pelton wheel is working under a head of 200 m and the rate of flow of water through the jet…

A: Given that, Head of pelton wheel, H=200 m,Flow rate of water through jet, Q=300 liters/sec,Mean…

Q: Q2/ Consider the following liquid level system shown below. The flow through the valve is related to…

A: Given Data:Find:Relationship between the head and time.

Q: The diameter of the pipe at the larger end is 0.50 cm and at the smaller end is 0.20 cm, the larger…

A: Larger end: D1= 0.50 cmZ1= 7 mV1= 1.2 m/sP1= 5200 kN/m2 Smaller end: D2= 0.20 cmZ2= 3 m   To find:…

Q: A Pitot tube is used to find stagnation pressure in relation to the static pressure port in an…

A: Given: at 10 km altitude  gauge pressure = 16.4 kPa

Q: A storage reservoir supplies water to a pressure turbine under a head of 20 m. If the flow rate is…

A:

Q: Question 1. A I m diameter pipe bend shown in the diagram is carrying crude oil ( S.G.=0.94 ) with a…

A:

Q: The total head of fan is 200m and has a static pressure of 201mm of water gage. What is the velocity…

A:

Q: Problem 5: Given a Crucible with a base diameter (Din)of 8 mm and the length (L) of the attached…

A:

Q: 5. Write down the Benoulli equation and explain the meaning of each terins 6. Water is flowing…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: If the velocity of water is 8 m/s and the pressure is 140 kPa on the discharge side of a pump. a.…

A:

Q: Question 1: B The diagram shows water leaving a tank through an inverted V-tube. (All answers to be…

A:

Q: 2 Oil flows from a tank through a 50 mm diameter pipe. If the average velocity is 1,3 m/s, determine…

A:

Q: A venturi meter has an inlet diameter of 65 mm and a throat diameter of 26 mm. When measuring the…

A: Given: A venturimeterinlet dia d1=65mm=0.65moutletthroatdiad2=26mm=0.026mmercury differential…

Q: Assuming hydrostatic pressure distributions, uniform velocity profiles and negligible viscous…

A:

Q: QI: In a venturemeter used for measuring the flow of oil (S = 0.85) through a horizontal pipeline,…

A: Given data:-specific gravity of flowing fluid, sl=0.85specific garvity of manometric fluid,…

Q: If the blood viscosity is 2.7x10-3 Pa.s, length of the blood vessel is 1 m, radius of the blood…

A:

Q: A pump discharges a liquid into a drum at the rate of 0.032 m3/s. The drum, 1.5m in diameter and…

A:

Q: The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The…

A:

Q: A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: The pressure through a section of pipe is 21 PSI and the velocity of the fluid is 1 ft/sec. If the…

A: given data; pressure at section 1st (P1)=21PSI=144789.903pavelocity at section…

Q: Transcribed Image Text:As part of a processing of biofuels, water is pumped into a circular tank…

A: Applying the conservation of…

Q: As part of a processing of biofuels, water is pumped into a circular tank with a diameter Dt, as…

A: For the solution refer below images.

Q: 2. The diameter of a pipe at the larger end is 0.5 cm and at the smaller end is 0.2 cm, the larger…

A: Data given - PA = 5200 kN/m2  VA = 1.2 m/s  DA = 0.5 cm  DB = 0.2 cm  ZA = 7 m  ZB = 3 m

Q: In the pumping system shown below, determine the following. a. Head loss at suction in m b. Head…

A:

Q: 5.4 A liquid, density 801 kg/m³ and viscosity 1.49 cp, is flowing in a horizontal pipe at a velocity…

A:

Q: A water pump develops a total head of 200 ft. The motor efficiency is 87.5%. If the power rate is…

A: Write the given data with suitable variables. H=200 ft=60.96 m0.3 mi ftη=87.5 %=0.875Q=1000…

Q: On average, you inhale approximately 1 L of air every 2 seconds. The pressure difference between the…

A: Given:To find:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.