Water enters through a 23.616 inches diameter pipe under a pressure of 14 kPa. It leaves through a 900mm diameter exhaust pipe with a pressure of 4 kPa. A vertical distance of 8.2 ft separates the centers of the two pipes at the sections where the pressures are measured. If 500 liters of water pass the motor each second, compute the power supplied to the motor.

Water enters through a 23.616 inches diameter pipe under a pressure of 14 kPa. It leaves through a 900mm diameter exhaust pipe with a pressure of 4 kPa. A vertical distance of 8.2 ft separates the centers of the two pipes at the sections where the pressures are measured. If 500 liters of water pass the motor each second, compute the power supplied to the motor.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As shown in Figure 4, a horizontal pipe with radius 0.0200 m bends straight upward througha height of 10.0 m and joins another horizontal pipe whose radius is 0.0400 m. If a liquid flows through the pipe, determine the volume flow rate that 6. will keep the pressures in the two horizontal pipes the same. V2 42 h V1
Problem 1 - Water is drawn into the pump, such that the pressure at the inlet A is -6 psi and the pressure at B is 20 psi. If the discharge at B is 4 ft³/s, determine the power output of the pump. Neglect friction losses. The pipe has a constant diameter of 4 in. Take h = 5 ft and p„ = 1.94 slug/ft.
Let the pressure gradient in the pipe be 1500 Pa/m and the diameter of the pipe be 4.0 mm. What is the average speed through this pipe of 20∘C motor oil? What is the average speed through this pipe of 100∘C motor oil?
Find the power (kW) if the area is 2.5 m2 and the head is 5 meters if water is running at 8 m/s.
A fire hydrant supplies water under a pressure of 190 kPa. A 100-mm-diameter hose is connected to it at A and the hose extends 40 m to the fire truck inlet at B. B Part A Determine the pressure of the water as it arrives at B. The friction loss is 1.5 m for every 10 m of hose. The inlet at Bis 0.5 m higher than the hydrant outlet. Express your answer to three significant figures and include the appropriate units.
Calculate the flow rate of the system by accepting the fluid passing through the reservoir-pipe system shown in the figure as ideal. As D1 = 0.5 m, D2 = 0.30 m and D3 = 0.40 m, determine the velocity heights in each pipe. Calculate and show the water levels in the pressure gauge pipes (it will be taken into account that the pressure gauge pipes are externally connected to the 1st and 2nd pipes, but the end of the pressure gauge pipe on the 3rd pipe is turned to the flow direction). Draw the relative energy and relative piezometer lines of the system.
Question 8 Two reservoirs are connected by a pipe whose total length is 360m.From the upper reservoir the pipe is 300mm in diameterfor a length of 150m and the remaining 210m is 450mm in diameter.The difference in water levels between the two reservoirs are 8m.Take f=0.006 for the smaller pipe and f=0.005 for the larger pipe.If all the changes in pipe sections are sharp and sudden, calculate the flow rate which can be delivered.
A pipe with a radius of 9 mm is attached to a nozzle. If the velocity of flow in the pipe is 2 m/s, what is the velocity of the flow at the nozzle when it is adjusted to have a diameter of 9 millimeters, and what is the flow rate?
A cylinder with a diameter of 0.5 m and a height of 1.8 m is shown below. The water flows through a flap valve (attached to the pair) with an opening of 0.075 m in diameter. It must be pushed up to open the valve. Determine the force to open the valve.
A certain process requires 2.2 cfs of water to be delivered at a pressure of 30 psi. This water comes from a large-diameter supply main in which the pressure remains at 60 psi. If the galvanized iron pipe connecting the two locations s 200 ft long and contains six threaded 90° elbows, determine the pipe diameter. Elevation differences are negligible. dx = ft
A jet of water is coming out from an inverted conical tank, which is full of water, through an orifice located in the side at 3 m from the top along the side of the tank. The tank is 4√5 m high and has a diameter at the top of 2 m. The vertex of the tank is 2 m above the ground level. If the coefficient of discharge is 0.62 and coefficient of velocity is 0.98, find the horizontal distance measured from the center of the conical tank to the point on the ground where the jet landed.
The pressure through a section of pipe is 23 PSI and the velocity of the fluid is 3 ft/sec. If the velocity was increased to 5 ft/sec, what would the pressure drop be?