The discharges from the pipe is 0.142 m3/s of water into a reservoir at a point 1.85 m below the water surface. At the point A diameter is 0.254 m and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm. If the head loss from A to the reservoir is 0.7 m, calculate the pressure in A.

The discharges from the pipe is 0.142 m3/s of water into a reservoir at a point 1.85 m below the water surface. At the point A diameter is 0.254 m and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm. If the head loss from A to the reservoir is 0.7 m, calculate the pressure in A.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The oil flows through the vertical venturi tube as shown in the figure. The venturi inlet has a diameter of 20 cm, the isthmus of the venturi is 10 cm in diameter, the pressure at inlet P1 is 41.4 kPa(gage), and the pressure at the isthmus P2 is the same size as the body of water. The same oil which is 1.52 m. Find the flow rate of this oil. The density of the oil is 849 kg/m3.
= 4.33 9.74m/ seć n/ 4(0.2)2 HOMEWORK Q1l A (30 N/s) flow throw the reducer of the proceeding problem ,the air in the (300mm) pipe having weight density of (9.8 N/m' ) in the flowing through the reducer producing a redaction of density .assuming that the weight density of the air in the (200 mm) pipe is (7.85 N/ m'). Calèulate the mass and volume flow rate. Q2/ (2) Water enters a conical diffusing passage (see Figure below). With a flow rate of 10ft'/s, and if the entrance cross-section area is 2 ft, what's the average velocity at the entrance to the diffuser? What must the diffuser exit area be to reduce the velocity to 0.5 ft/s? 4 = 2 f Q = 10 cfs - m = AQ: oiclooleo or boon ow.matve binl to sinsb omit letot odi stum hn th .C
A 50-mm diameter siphon is drawing oil (S.G. = 0.82) from an oil reservoir as shown. If the head loss from point 1 to point 2 is 1.50m and from point 2 to point 3 is 2.40m, find the discharge of oil from the siphon and the oil pressure at point 2. 2.00 m 50-mm-diameter siphon Oil (s.g. = 0.82) 5.00 m
The turbine at C draws a power P kW. If the intake B has a diameter of de mm. The pressure dg(mm) dĄ(mm) at the intake B is Ps kPa and the velocity of the water (density = 1kg/L) at that point is v (m/s). The frictional losses between A and B are At neglected, and the exit A has a diameter of da B1 mm. Consider the data in the table to M = last two digits of your student ID P (kW) = 0.5M + 68.5 da(mm) = M + 150 dp (mm) %3D М + 400 PB (kPa) = M + 380 v (m/s) = 0.1M + 4 a- Calculate the velocity at the exit A b- Calculate the discharge at the exit A c- Calculate the turbine head d- Calculate the pressure at A m=13
Water flows in a D = 36 mm diameter pipe as shown in the figure. Since Q = 60 m3 / h, and the density of %3D water is 1000 kg / m³, calculate the resultant force on the elbow and the angle it makes with the horizontal. 120°
Oil of density ρ=880 kg / m3 flows through the Venturi tube (pictured). Calculate the flow if given: D=24 mm, d=12 mm, h=440 mm. Need to solve it with bernoulli's equation.
At point A where the diameter at of the pipe is 18 cm the pressure reading is 22.5 cm of Mercury. At point B, 3 m lower than A, the diameter is 48 cm and the pressure reading is 50 cm of Mercury. If the total head loss between the two points is 1.50 m, solve for the discharge. Water is flowing through the pipe. subject: hydraulics
Water is discharged from a reservoir into the atmosphere through a 80 m long pipe. There is a sharp entrance to the pipe and the diameter is 250 mm for the first 50 m. The outlet is 35 m below the surface level in the reservoir. The pipe then enlarges suddenly to 450 mm in diameter for the reminder of its length. Take f 0.004 for both pipes. Calculate the discharge.
AA cir Water is flowing through a horizontal pipe of diameter 200 mm at a velocity of 3 m/s. A circular solid plate of diameter 150 mm is placed in the pipe to obstruct the flow. Find the loss of head due to obstruction in the pipe if C = 0.62.
Water flows from a nozzle with a speed of V = 10m/s Stream diameter = 0.1 m Nozzle -- Moving control volume and is collected in a container that moves toward the V = 10 m/s nozzle with a speed of Vcy = 2 m/s as shown in the figure. If the water between the nozzle and the tank is in the constant diameter stream, what is the accumu- V = 2 m/s 3 m lation rate of water in the tank?
2) The horizontal pipe of diameter 240 mm is suddenly enlargement to a diameter of 480 mm. if the pipe carries water at 325 liters/sec, calculate the (i) Head loss to sudden enlargement,(ii) Pressure loss across the enlargement (p1-p2).
A pipe whose axis is horizontal, is full of water in motion. At a section A, the velocity of water is recorded as 54000dm/hrandd the pressure is equilavent tp 14.07m of water. if the pipe tapers gradually from 150mm diameter to A to 100mm diameter at B. determine the preesure at B.