Water is filled into a circular tank (inner diameter 1 m) from two inlet pipes as shown. The volumetric flow rate at inlet 1 is 120 liters/hour. Determine the rate at which the level of water in the tank rises as a function of the volumetric flow rate at inlet 2. Plot the results (rate of level rise vs. volumetric flow rate) for the range between 0 Inlet 1 Inlet 2

Water is filled into a circular tank (inner diameter 1 m) from two inlet pipes as shown. The volumetric flow rate at inlet 1 is 120 liters/hour. Determine the rate at which the level of water in the tank rises as a function of the volumetric flow rate at inlet 2. Plot the results (rate of level rise vs. volumetric flow rate) for the range between 0 Inlet 1 Inlet 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

0.95 m3/sec flow rate of water flows downwards in a pipe as shown in figure. If the pressures at points 1 and 2 are to be equal. Determine the diameter of the pipe at point 2.The velocity at point 1 is 6.5 m/sec and the diameter of pipe at point 1 is 330 mm. The height between point 1 and point 2 is 2.8 m?
2. Air flows at the rate of 1.5 m²/s through a horizontal pipe with a gradually reducing cross section as shown in the figure. The two cross-sections of the pipe have diameters of 400 mm and 200 mm. Take the air density as 1.2 kg/m² and assume inviscid incompressible flow. The change in pressure (P2-P1) (in kPa) between sections 1 and 2 is 200 mm Air Flow 400 mm 1.5 m/s (A) -1.28 (B) 2.56 (C) -2.13 (D) 1.28
Q2l Calculate size of each part for the air conditioning ducts system shown in Figure(1) by using equilibrium pressure drop method. The velocity of air in main duct 7 m/s. Tabulate the results (velocity value, rate of pressure drop, circular diameter, and air flow rate) for each part, then convert circular ducts to equivalent rectangle ducts at height 300 mm for all system. 0.5 m³/s E 5m A D 0.5m³/s 3m B Figure (1) 3m 3m 5m C 1 m³/s
Water flows through a Venturi meter, as shown in the figure. The pressures of the water at locations a and b in the pipe support columns of water that differ in height by L = 10 in. The atmospheric pressure is 14.7 lbf/in2, the specific volume of water is 0.01604 ft³/lb, and the acceleration of gravity is g = 32.0 ft/s². Patm = 14.7 lbf/in.² g= 32.0 ft/s² * Your answer is incorrect. Water v = 0.01604 ft³/lb Determine the difference in pressure between points a and b, in lbf/in². Does the pressure increase or decrease from point a to point b? Determine the difference in pressure between points a and b, in lbf/in². Pb-Po= i 16.56 lbf/in²
115 m turbine 2 In the above example problem, a hydroelectric turbine at the base of a dam is shown schematically. The height of the water above the turbine station given as 115 m. This turbine produces 4.6 MW of electricity, and you may assume the losses in the system to be equivalent to 10 m of head of water. The diameter of the pipe at the turbine exit is 0.75 m, and the velocity of water exiting from the pipe is 12.5 m/s. Caleulate the efficiency of the turbine.
3. A pipe with varying cross-sectional areas is set up vertically as shown in the drawing. Water enters the pipe from the top wider end at a speed of 300 cm/s. Calculate (a) the mass flow rate of water (the amount of mass entering/exiting the piper every second) and (b) the water pressure at the bottom narrower end section of the piper. (Density of water is p = 1000 kg/m2 1.00 g/cm')) P 1.20x10 Pa 10.0 cm h=4.00 m 2.50 cm2 P= ?
Water is pumped from a pond to a tank by using a pump at a rate of 55 dm/s through a 50.4-mm-diameter steel pipe. The total length of the pipe is 95 m, and the viscosity of water is 1 mm2/s. Calculate the power required in the pump to maintain the discharge. Refer to Figure Q1 to include all losses in your calculation. (2) 20 m Gate Valve Pump (Fully Opened) 2 m Globe Valve (75% Opened) Figure Q1
A tube with 45 meters long, and a diameter of 1.8 meters and 2.3 meters, inlet and outlet respectively. Water is flowing inside the tube. What is the rate of change of the velocity with respect to its length when the inlet has a velocity of 2100 meters/min?
Water flows in pipes A and B and converges into pipe C as shown in the figure. If the flow rate at pipe C is 50 L/s and the velocity at pipe A is 4 m/s, determine the velocity (in m/s) of water at pipe B. da = 100 mm dc = 300 mm B dB = 200 mm a. 0.019 b.0.031 c.0.592 d.0.707 The 75-mm water main pipe in your street has a pressure of 200 kPa and carries 25 lps of flow. You want to store water into an elevated tank, 12 m above the water main, so there is adequate flow in your 3rd level bathroom. Assume the total losses from the water main to the water tank is 10 m. Determine the rated power (in kW) of a household pump required if the pump has an efficiency of 80% and the air pressure in the partially full tank is 300 kPa. The flow through the pump is 3 lps. a.6.00 b.1.12 c.9.37 d.0.72
The pressure loss p in a pipe is related to the flow rate Q by the equation P = KQ^n, where K and n are constants. If K = 190 x 10³determine the value for n when a flow rate of Q = 0.04 m³/s causes a pressure loss of 180 Pascals.
Water flows at the rate of 5 ft/s through an inclined pipe. At point A, where the diameter is 12 inches, the pressure is 15 psi. At point B, the diameter is 6 inches and the center of the pipe is 2 feet lower than at point A. a. Draw a clear diagram of the pipe system that indicates the following: (a-1) water flow reflecting the quantities involved in describing fluid flow and (a-2) the object of interest and the quantities that describe Bernoulli's equation. b. Write the Bernoulli's Equation using subscripts U ad L for the upper and lower points respectively and determine the pressure at point B?
A 75-mm diameter pipe is connected to a 100-mm diameter pipe. If the velocity of flow in the 75-mm pipe is 2 m/s, what is the velocity of flow in the 100-mm pipe? What is the flow rate in the 75-mm pipe in m^3/s?