The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis. 3.1 Find the maximum allowable speed to operate the pump 3.2 What power is expected in overcoming friction at this speed, take f = 0.01

The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis. 3.1 Find the maximum allowable speed to operate the pump 3.2 What power is expected in overcoming friction at this speed, take f = 0.01

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump with an impeller diameter of 300 mm running at a speed of 2950 rev/min delivering 450 L/min of water at a head of 350 kPa is going to be replaced by a geometrically similar spare pump running at a speed of 1450 rev/min delivering the same flow rate and head. Determine the impeller size of the spare pump and the percentage increase (decrease) of power required for the spare pump. OL. 380.1 mm; a decrease of 61.33% OI., 380.1 mm; an increase of 38.77% I. 147.5 mm; an increase of 3.4% IV. 210.3 mm; a decrease of 83.1%
can you please find the solution
a. the total dynamic head in meters b. the water power in kW c. the motor horsepower if the pump efficiency is 66%
A centrifugal pump running at 1859 rpm has impeller dimensions of b₁ = 53, b₂ = 21, r₂ = 285, r₁ = 82, B₁ = 20°, B₂ = 10° (all dimensions in mm). Determine the theoretical head (meters) if water enters the blades radially. Round off your answers to 2 decimal places. (15 mins)
Centrifugal pump has differential pressure 15 bar and use to transport oil between two separators. If the pressure at first separator is 4 bar calculate the pressure at second separator and NPSH. Where: Suction and discharge pipe diameters = 10 inch, Suction pipe length = 16 m, ld Oil level at first separator 3 m2d Oil density=880 kg/m³ P Oil flow rate=0.092 m³/sec e Pipe roughness= 0.045 mm Discharge pipe length = 25 m O Oil level at second separator = 5.5 m2d Oil viscosity = 9.5 x 10³ Pa.s Oil vapor pressure 22.5 kPa d кра 4.5x10²
Analyze to select the type of the turbine when its diameter is 600 mm, rotational speed is 600 rpm and working under a water head of 120 meters. The buckets deflect the 100 mm diameter jet through an angle of 165°. Take the coefficient of velocity for the nozzle as 0.97. Use Table given below for selection of turbine. Sr. # Specific speed (rpm) Type of turbine 1 8-30 Pelton wheel with one nozzle 30 - 50 Pelton wheel with 2 or more nozzles 50-250 Francis turbine 4 250-1000 Kaplan turbine 2. 3.
Give detailed solution,Only Handwritten.
Find the force required to hold the blade in position, if the jet weight (100kg) and discharge (4001/sec) Air 25 kPa Blade Water 3m 65 Jet W
Water 2. In this system, d = 6 in., D = 6 ft, and =z2 = 12 ft. The water in the system is 13 cfs. machine a pump or a turbine? pressures at points A and B? losses. Pump 1. The discharge in the siphon is 2.80 cfs, D = 10 in., L1 = 3 ft, and L2 = 3 ft. Determine the head loss between the reservoir surface and point C. Determine the pressure at point B if three-quarters of the head loss (as found above) occurs between the reservoir surface and point B. 1 m REVIEW Home Work (1) Energy Equation Water T = 10ºC REPPER Water Same elevation Machine Elevation = 40 m -Elevation = 20 m Elevation 10 m 300 m + -300 m- 4. Assume that the head loss in the pipe is given by hL = 0.014(L/D)(V2/2g), where L is the length of pipe and AZ₂ AFL B Elevation 100 m L = 100 m D = 60 cm Water T= 10°C 3. A water discharge of 10 m3/s is to flow through this horizontal pipe, which is 1 m in diameter. If the head loss is given as 7V2/2g (V is velocity in the pipe), how much power will have to be supplied to the flow…
= constant Q16/ A pipe diameter of 400 mm carries water at a velocity of 25 m/s. The pressures at the points A and B are given as 29.43 N/cm² and 22.563 N/cm² respectively while the datum head at A and B are 28 m and 30 m. Find the loss of head between A and B. Z شكر الكائر 2B ADA=400 mm PA 29.43 N/cm #28 m ZA 28 Dg= 400 mm Pe = 22.563 N/cm ZB = 30 m DATUM LINE
A3
A pump is delivering 160 liters per second of water using an impeller diameter of 254mm and operating at a speed of 1800 rpm. If the speed is held constant and the impeller diameter is changed to 203.2 mm, what is the new discharged of the pump in liters per second?(128 L/s)