4 mm drill holes in the large water tank causing water to flow out of the tank into a single propeller with arc angle = 180 degrees as shown in Fig. Assuming no friction is involved, calculate 1) The velocity of the water flowing out of the borehole (V) 2) If a single propeller is attached to the ground (U=0), what is the force against the propeller? 3) If a single propeller moves to the right with a speed U=2 m/s, what is the force on the impeller? 4) Find the power generated by the impact of the water in the case of a single propeller moving at a speed U=2 m. /s

Q: (See Fluids in the News article titled "Where the plume goes".) Air flows into the jet engine shown…

A:

Q: A water pump produces a flow of 0.25 m/s and a power of 2 kW, using an 300-mm-diameter impeller.…

A: Given:Q1=0.25 m3/sP=2 KWd1=300 mm

Q: Find acceleration U = 2.23 mis V = 4mls S umis +-25

A: Given data : Initial velocity=U Final velocity=V Time=t   Required : Acceleration

Q: QUESTION 1 A jet of freshwater strikes a series of vanes of a turbine at 25° with the direction of…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: In the arrangement in the figure, the reels 'a 'and 'b' are pulled at VA m/s and VB =12 m/s. since…

A: given data

Q: 6) A screw jack is used to lift a mass of 500kg. The screw has a thread with a pitch of 8 mm. An…

A:

Q: For the Fig. shown, find the velocity of point 1 and the pressure of point 2 D2=20 cm

A:

Q: There are two coaxial cylindrical tubes of radius kR (the smallest) and R, between which is a…

A:

Q: s is 2.5 m. The turbine U power under a heac tational speed of 420

A:

Q: (Moment-of-momentum) A lawn sprinkler is constructed from pipe with 0.226-in. inside diameter as…

A: d=.226 in=.0188ft r1=r2=5.54 in=.462 ftr=2.77 in =.231 Since diameter is same and mass flow rate is…

Q: ▸ A Pelton wheel of 1 meter diameter is working under a head of 550 meter. Find the speed of the…

A:

Q: In the figure shown, the vane turns the water jet completely around. Find the maximum jet velocity…

A:

Q: In the figure the V-shaped pipe is filled with water, it is desired that the liquid remains in the…

A: The centrifugal force derives from the inertia of the moving body and is directed outwards from the…

Q: The pump shown draws water from reservoir A at elevation 10 m and lifts it to reservoir B at…

A:

Q: Example 4-6: The water flows through the pipe bend with a discharge of 200Ls. The bend is placed…

A: To Find:  The magnitude and direction of the force of water on the bend. Given : The discharge is…

Q: Find acceleration Initial velocity=2 m/s Final velocity=2.6 m/s time=2 s

A: Given data : Initial velocity=U Final velocity=V Time=t   To find : Acceleration

Q: For the Fig. shown, find the velocity of point 1 and the pressure of point 3 D2=20 cm P2=100 Kpa…

A:

Q: A Centrifugal pump discharges water with a volume flow rate of 110 liters per second. The inlet…

A:

Q: b) To slow the boat very quickly a thrust reverser (or speed brake) is deployed (as shown in the…

A: Given data :-Velocity of V1=V2= VNozzle area (a) = a2Angle = 90°Find out :-  Thrust force on the…

Q: 3. The figure shows a two-dimensional cascade of identical vanes, which deflect the flow through an…

A: Step 1: Step 2: Step 3:

Q: Two geometrically similar pumps are running at the speed of 1500rpm and 3000rpm. One pump has an…

A:

Q: 3. The equation v,-v= 2as gives the final velocity (v.) of a body which started with an inilial…

A: Given Motion equation Head loss equation To find Dimension prove

Q: A 20 mm diameter pipe forks, two branches being 10 mm in diameter  and the other 15 mm in diameter.…

A: To draw: The neat sketch and the velocity in the 10 mm diameter pipes. Given: The diameter of inlet…

Q: A fireboat is putting out a blaze from a beach bonfire that got out of hand. If the nozzle angle is…

A:

Q: 3.2 Perhaps you have felt the end of a garden hose exert a backward force on your hand if (and only…

A: Solution: Given Data: Q=1 L/s=1000 cm3/sA=1 cm2a=0.5 cm2   Note: Dear Student! As per our…

Q: Propeller blades in aeroplane are 2 m long. when propeller is rotating at 1800 rev/min, compute the…

A: here for tengential velocity at the tip of the blade radius = 2 m. and Vt = 2*pi*R*N / 60 m/s

Q: Find the final velocity of car Initial velcoity =0 m/s Acceleration=12 m/s2 Time=4 s

A: Given data : Initial velocity U=0 m/s Time t=4 s Acceleration a=12 m/s2   Required : Final velocity…

Q: A certain fan delivers 340 m/min of air at a static pressure of 25.4 mm of water gage when operating…

A: Calculate the rpm of the desired fan using the relation between volume flow rate and rpm. N2N1=Q2Q1…

Q: Compute the torque to be applied by the servo motor fixed to the pin at point

A: Torque applied by servo motor is required

Q: Problem-5: A Plunger is fitted to a vertical pipe filled with water. The lower end of the pipe is…

A: Givena=5 m/s2hatm=10mhv=2mg=10 m/s2

Q: The nominal power of the wind turbine is 2 MW at wind speed 11.5m/s, generator efficiency is 94%,…

A:

Q: Q.1). The figure below shows a smooth curved vane attached to a rigid foundation. The jet of water,…

A:

Q: assume that the wedge makes a constant angle of ? = 19.0°. Suppose you want the wedge and the rod to…

A:

Q: Derive the energy equation from Reynolds transport theorem

A: following is the answer-

Q: Write the difference between linear and angular momentum.

A: The linear momentum is a vector quantity. Mathematically it can be expressed as, P→=mV→ Where P is…

Q: 5. A sprinkler rotates around fixed Point C. The nozzle on Arm A has broken off. So, water exits Arm…

A:

Q: Draw a velocity triangle as shown in the figure in question. The velocity triangle immediately after…

A: The velocity drawing of the impeller

Q: The conveyor belt shown below runs at a constant speed vp, uphill at an angle 0 relative to…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.