A water jet hits a wing on a moving vehicle, splitting the water jet in quantity and diameter, with half going in one direction and half in the other. The initial velocity of the water in the jet is 50 m/s and the car is moving at 10 m/s. What is the diameter of the jet of water if the component applied by the water jet on the wing is 3600 N and the force in the x direction is 2 times greater than the force in the y direction? If necessary, psu = 1000 kg/m3, g = 9.81m/s2 should be taken.

A water jet hits a wing on a moving vehicle, splitting the water jet in quantity and diameter, with half going in one direction and half in the other. The initial velocity of the water in the jet is 50 m/s and the car is moving at 10 m/s. What is the diameter of the jet of water if the component applied by the water jet on the wing is 3600 N and the force in the x direction is 2 times greater than the force in the y direction? If necessary, psu = 1000 kg/m3, g = 9.81m/s2 should be taken.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In an experiment a jet of water of diameter 20 mm is fired vertically upwards at a sprung target thatdeflects the water at an angle of 120° to the horizontal in all directions. If a 500g mass placed on thetarget balances the force of the jet, what is the discharge of the jet in litre/s?
I need the answer as soon as possible
Water leaves a hose at a rate of 3.6-kg per 2.0-s with a speed of 19.3-m/s and is aimed at a toy car at the exact moment the car is hit the water slows down to 4.0-m/s (That is, we ignore any splashing back.) What is the force exerted by the water on the toy car?
A water jet of an area of 0.03 m² impinges normal on a fixed plate. If a force of 1 kN is produced as a result of the impact, the velocity of the jet would be
A pipe of diameter 10cm conveying 200 liters/s of water has bend of angle (θ = 90⁰) and θ = 0⁰ through horizontal plane. Find theresultant force exerted on the bend if the pressure at the inlet and outlet of the bend are 15N/cm2 and 10 N/cm2respectively
Water with a density of 1.94 slug/ft³ is in a cart. Water is ejected from the cart with a velocity of 45 ft/s and a flow rate of 200 gal/min. It leaves at an angle of 60°. Assume the water inside the cart is motionless. a. Sketch the control volume b. Find the force F required to keep the cart in place 45 ft/s 60°
A jet of 50mm diameter impinges on a curved vane and is deflected through an angle of 175 degree. The vane moves in the same direction as that of jet with a velocity of 35m / s. If the rate of flow is 170 L / s, determine the component of force on the vane in the direction of motion. How much would be the power developed by the vane and what would be the water efficiency? Neglect friction.
The density of the liquid striking the "splitter" of Figure 6.15 is 830 Kg/m. Dėtermine the force components of the force on the splittèr. Assume a smooth entry / sliding of the stream of liquid. (10) 2 số° Fy 2 Fx cs 30 Q,-0.03 cms Vo = 10 m/s cs 45° Qo= 0.10 cms FIGURE 6.15
A jet of 50mm diameter impinges on a curved vane and is deflected through an angle of 175 degree. The vane moves in the same direction as that of jet with a velocity of 35m/s. if the rate of flow is 170 L/s, determine the component of force on the vane in the direction of motion. How much would be the power developed by the vane and what would be the water efficiency? Neglect friction.
A water jet with a flow rate of 2.83 m3 / s is traveling at 6 m / s in the positive x direction. The cost of the current striking a stationary splitter is correct about a 45 aç angle, other company are deflected downwards by the same angle and the final velocities of the two streams are 6 m / s. By neglecting the gravity, the separator is in place against the force applied by the water. calculate the x- and z- power of what is required to hold it. For water ? = 1.184 kg / m3
Homework A circular jet of water at 20°C Implnges on the vane shown In flgure. The Incident jet has a velocity of 25 m/s and a dlameter of 200 mm. The vane divides the Incident jet equally, and the jet exits the vane as two jets, each making an angle of 200 with the Incoming Jet. (a) Determine the force on the vane when the vane 200 mm 25 m/s- 20° V. Incident jet Moving vane Is moving at a speed of 15 m/s In the same directlon as that of the Incident jet. (b) Determine the force on the vane when the vane Is moving at a speed of 15 m/s In the opposite dlirection to that of the Incident jet. Assume water at 20°C.
A very popular toy on the market several years ago was the water rocket. Water (at 10°C) was loaded into a plastic rocket and pressurized with a hand pump. The rocket was released and would travel a considerable distance in the air. Assume that a water rocket has a mass of 50 g and is charged with 100 g of water. The pressure inside the rocket is 100 kPa gage. The exit area is one-tenth of the chamber crosssectional area. The inside diameter of the rocket is 5 cm. Assume that Bernoulli's equation is valid for the water flow inside the rocket. Neglecting air friction, calculate the maximum velocity it will attain. 5 cm PROBLEM 6.90 100 kPa