A single plate clutch, effective on both sides, is required to transmit 75 kW at 1000 rpm. Determine the outer radii of frictional surface when the ratio of radii is 1.75 and the maximum pressure is not to exceed 0.5 MPa. Also determine the axial thrust to be provided by springs. The mean radius of the frictional surface for uniform wear is 110 mm.

Q: Question 3 An engine of a 2 ton truck develop 30 kW at 600 rpm. The truck is fitted with a cone…

A: For answer refer the next page.

Q: A multiple vee-belt drive is required to transmit 4 kW. The smaller pulley has of the system has a…

A: The power transmitted, P = 4 kWThe diameter of the smaller pulley, d = 150 mmThe speed of the…

Q: A multiplate friction clutch is required to transmit 72 kW at 3600 r.p.m. The plates are alternately…

A: Given data: -  The power transmitted by the clutch is P = 72 kW. The speed of the clutch is N =…

Q: The two square-jaw grips have the dimensions shown in the figure and are made of mild steel. The…

A: Power transmitted (P) = 1.8 kWRotational speed (n) = 600 rpmTo calculate:The surface pressure on the…

Q: Two machines are coupled by means of a clutch plate with 2 contact surfaces. The plate has an inner…

A: GIVEN WE have,contact surface clutch plate inner diameter (d1 )=130mm=0.13mtrouter diameter (d2…

Q: A worm running at 2000rev/min is to drive a worm wheel at 200 rev/min and to transmit to it 15kW.…

A:

Q: THE ENGINE OF AN AUTOMOBILE IS RATED TO GIVE SOKWAT 200 RPM WITH A MAXIMUM TORQUE OF 600 N-M. DESIGN…

A: The answer is mention below

Q: A conical clutch has an included angle of 150. The outer and inner diameters are 100 and 40 mm…

A: Given data:Since, the clutch is of two halves.So, the cone angle of the clutch isOuter diameter,…

Q: 02 A conical clutch an included angle of 60°. the outer radius and inner diameters are 80 and 20 cm…

A:

Q: (b) A single plate clutch has a driven plate with an annular friction lining of 380 mm outside…

A: Given: Outside diameter, D = 380 mm or 0.38 m Inside diameter, d = 270 mm or 0.27 m Pressure, P =…

Q: An automobile single plate ciutch consists of a pair of contacting surtaces. The inneOr and outer…

A:

Q: A multi-plate clutch has four pairs of frictional surfaces, each of internal diameter 120 mm and…

A: Clutch is defined as a machine element which is used to engage and disengage driver and driven shaft…

Q: The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley…

A: diameter of pulley (d) = 110 mm  no of belt = n = 2 groove angle =  2β = 45° = β = 22.5° power…

Q: Q) A single plate clutch has to transmit 75 kW at 3000 r.p.m. The spring exerts an axial pressure of…

A: The answer is

Q: l-plate clutch must transmit 23 kW of power without slipping at 2500 rev/min. The coefficient of…

A:

Q: A single plate cutch consists of one pair of contacting surfaces. The inner and outer diameters of…

A: Given Data Inner diameter of clutch is: di=100 mm=ri=50 mm Outer diameter of clutch is: do=150…

Q: A disc clutch is required yo transmit 5 kW at 2000 rpm with coefficient of friction 0.25 and bore…

A: Given                      Power, P = 5 kW Coefficient of friction = 0.25  Constant pressure, P = 1…

Q: (b) A multiple plate clutch has more number of clutch plates. A typical clutch consist of the…

A:

Q: A conical clutch has an included angle of 105°. The outer and inner diameters are 110 mm and 40 mm,…

A: Consider 'W' be the axial load on the clutch, R and r be the outer and inner radii of the clutch…

Q: A multi disc clutch, as illustrated below, is used to connect a four-cylinder internal combustion…

A: Friction Clutch Friction clutch is used to transmit the power in shafts and machines which must be…

Q: A multiple disk clutch consisting of 3 disks on the driving shaft and 2 disks on the driven shaft is…

A:

Q: 92 A dry single plate clutch is to be designed for an automotive wehicle whose engine is rated to…

A: radius of the friction plate = r1  Inner radius of the friction plate = r2  r1 = 1.25 r2

Q: A single-plate clutch has a friction disc with inner and outer radii of 20 mm and 40 mm,…

A: Uniform pressure theory is when the product of pressure and area of the contacting surface…

Q: The disc clutch has a pair of mating friction surfaces, with an outer diameter of 350 mm and an…

A: Given data:- outer diameter=350 mm inner diameter =250 mm The average value of the coefficient of…

Q: In a thrust bearing, the external and the intermal diameters of the contacting surfaces are 320 mm…

A:

Q: A conical clutch has an inclined angle of 120. The outer and inner diameters are 80 mm and 20 mm…

A: The answer is given in the following step

Q: Determine the resulting torque of a uniform pressure frictional clutch having 4 discs in the driving…

A:

Q: The clutch of a motor car is required to transmit 9 kW at 3500 rpm. It is of single-plate type, with…

A: Given: The power of the motor is 9 kW. The coefficient of friction is 0.25. The maximum pressure is…

Q: 3/ A multi- plate clutch is to transmit 12 kW at 1500 r.p.m. The inner and outer dii for the plates…

A: Given data as per the question Power transmitted =12 kw speed =1500 rpm spring force =1kN angular…

Q: Q6 Engine developing power at 1000rpm is fitted with a cone clutch having the face width of the…

A: To calculate the mean diameter of the cone clutch, developing power and the constructionspeed of the…

Q: A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has a face angle of 10◦ The width of the…

A: Given data:

Q: A car engine has its rated output of 16 kW. The 2 maximum torque developed is 120 N-m. The clutch…

A: Given data as per the question power of car engine =16 kwMaximum torque developed =120 N.maxial…

Q: For the same question, the Impeller hub will be pressed onto the taper shaft with the Nut. How much…

A: given data; ⇒engine power(P)=27kw                        =27*103w⇒speed (n)=1684rpm⇒conical…

Q: Consider a 2D geometry (half-circle of radius R) of solid material maintained at a uniform…

A: we have to find out the heat energy supplied to replenish the deficit due to environmental loss

Q: A leather-faced cone clutch has a contact surface with a mean diameter of 15 in. and transinits 20…

A: Given: Mean diameter, dm = 15 in or 1.25 ft Power transmitted, P = 20 hp or 11000 lb.ft/s Rotational…

Q: The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: Given, Coefficient of friction, μ=0.15 Weight of the handle, W=15 N Applied force to the end of the…

Q: A multi plate friction clutch is used to transmit the power from the engine to a rotor which has a…

A: The above question is based on multi plate clutch design.

Q: Exomple: An automotive single-plate clutch with o pairs of frichon Surfaces, tvansmits a 300. N-m…

A: For single plate clutch : Torque (T)=300 N-m speed (N)= 1500 rpm inner dia.(d) = 170 mm outer…

Q: The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.