5. A pump draws water from reservoir A and lifts it to reservoir B. The loss of head from A to 1 is three times the velocity head in the 150mm pipe and the loss of head from 2 to B is twenty times the velocity head in the 100mm pipe. Discharge is 20L/s. a. Calculate the horsepower output of the pump in kw. b. Calculate the pressure head at 1 in meters. c. Calculate the pressure head at 2 in meters. El.240 m El. Om El. -20m 150mm J00 mm

5. A pump draws water from reservoir A and lifts it to reservoir B. The loss of head from A to 1 is three times the velocity head in the 150mm pipe and the loss of head from 2 to B is twenty times the velocity head in the 100mm pipe. Discharge is 20L/s. a. Calculate the horsepower output of the pump in kw. b. Calculate the pressure head at 1 in meters. c. Calculate the pressure head at 2 in meters. El.240 m El. Om El. -20m 150mm J00 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pump is used in a building to lift water from a ground floor. The pump is pushing 60l/sec of water through a 0.1m diameter to above floor which is 5m high. Calculate the velocity by which the water exits the pipe if water enters the pump at 30kPa and exists with 5kPa.
a pump at 1750 rpm delivering 600 rpm aganist a total head of 200 tt. change in the filling system have increase the head of 450 feet. at what rpm should the pump be operate to achieve this new head at the efficiency?
▸ A Pelton wheel has a mean bucket speed of 15 m/s with a jet of water impinging with a velocity of 40 m/s and discharging 0.45 m³/s. If the buckets deflect the jet through an angle of 165°, find the power generated by the wheel.
1. Water enters through a 23.616 inches diameter pipe under a pressure of 14 kPa. It leaves through a 900mm diameter exhaust pipe with a pressure of 4 kPa. A vertical distance of 8.2 ft separates the centers of the two pipes at the sections where the pressures are measured. If 500 liters of water pass the motor each second, compute the power supplied to the motor.
Need help with this problem
Determine the power requirement of the pump shown in Figure 3.0, assuming it has an efficiency of 88%. The system has a loss coefficient of 3.0 up to point A, and K =1.2 from point B to point C. Neglect any losses through the exit nozzle. Additionally, compute the pressures at points A and B. Water 15 m 2 cm 4 cm dia. 5 cm dia. Figure 3.0 400 kPa
1.Find the diameter of a pipe of length 3000 m when the rate of flow of water through the pipe is 300 litres/s and the head lost due to friction is 5 m. Take the value of C = 50 in Chezy’s formula.
Number 4 only. will upvote anyone who will answer. Fluid mechanics. Thank you
If the pump needs to lift a water to an elevation of 20m from its centerline while the water source is 5m above pump centerline and the flow rate is 50 GPM, compute the motor horsepower needed if the pump efficiency is 85%. NEEDS COMPLETE SOLUTION, AS SOON AS POSSIBLE.
5
Plot the variation of pressure with area for four different pump speeds. COURE NAME: THERMOFLUIDS
Find the offset angle for an axial pump that delivers 50 gpm at 1750 rpm. The volumetric efficiency is 95%. The pump has a nine 0.75 inch diameter pistons arranged on a 6-in piston circle diameter.