Answered: 8.61 cally through a 200-fi-long,…

8.61 cally through a 200-fi-long, 1.0-in.-diameter drawn tubing at a rate of 0.060 ft'/s if the pressures at the inlet and outlet are the same? Pu

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 1.A liquid refrigerant (sg = 1.080) is flowing at a weight flow rate of 23.0 N/h. Required…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: 5- Compare the reading of pitot tube and the reading of anemometer to the measurement of air…

A: An anemometer is a device which is used to evaluate the velocity of the air by counting the number…

Q: 10. What hose I.D. would be required to deliver 50 gal/min , assuming no friction losses at a…

A: GivenQ=50gal/min=0.189271 m3/minQ=3.1545×10-3 m3/sV=8.5ft/sec=2.5908 m/s

Q: Differentiate between major and minor losses in pipes.

A: Pipe is a closed conduct which is used for caring fluids under pressure because pipe carry fluids…

Q: FIGURE 4.13 Figure for Problems 4-3 and 4-4. 4-3 Shown in Fig. 4.13 is a vertical-walled storage…

A: (a) Volume stored is calculated as: V=Net volume flow rate ×TimeA×h(t)=(q0-qout)th(t)=(q0-qout)tA…

Q: ( Use nomograph AND the formula) Size a pipe that will not exceed 48' of HL in 6000 feet of pipe at…

A: Given data: Head loss, HL = head loss due to friction, Hf= 48 ft Length of the pipe, L = 6000 ft…

Q: A pipe handles a flow rate of 0.002 m³/s. Find the minimum inside diameter that will provide an…

A: To find: The minimum inside diameter. Given: The flow rate is Q=0.002 m3/s. The fluid velocity is…

Q: During Extension of vertical cylinder At Extension (when cylinder is stopped) Pressure Reading PSI…

Q: At a flow rate of 30 LPM, what will happen if the pressure stays the same in 30, 60, and 90 seconds…

A: The flow rate of the fluid:Hydrostatic pressure:

Q: Compute points on the velocity profile from the pipe wall to the centerline of a 3/4-in Type K…

A: Given: The diameter of the pipe, d = 3/4 in The volume flow rate, Q = 0.5 gal/min The temperature of…

Q: An oil with a dynamic viscosity of 0.8 Pa.s and specific gravity of 0.9 is flowing through a…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: When 1,800 l/min flows through a 200 mm diameter pipe, which later is reduced to 100 mm, what will…

Q: ith a velovity of 2ft/s. What is the kinwtic energy of the water in ft.lbf/lbm?

A: given:velocity v= 2ft/sdiameter d=1.5in

Q: 8. In the regenerative circuit shown below, the pump's flow rate is 10 gpm. If the piston diameter…

A: given data; ⇒flow rate (Q)=10gpm=6.309*10-5m3/s⇒piston diamter (d1)=7 in=0.1778m⇒rod diamter(d2)=5…

Q: The effect of parallel tubes on flow rate The effect of parallel tubes on flow rate. A: the fluid…

A: The human circulatory system is made up of a network of arteries, veins, and capillaries that are…

Q: Water at 60°F and one atmosphere is being transferred from tank 1 to tank 2 with a 2-hp pump that is…

A: As per the guidelines I can solve only first three subparts. Repost the other part.

Q: Pure milk at 293 K has a density of 1030 kg / m3 and a viscosity of 2.12 cp flowing at a rate of…

A: Write the given data with suitable variables: ρ=1030 kg/m3μ=2.12 cp=2.12×10-3 Pa-s10-3 Ps-s1…

Q: Q.1. Calculate the weight of tubing in vertical well with no fluid present inside the wellbore for…

A: The weight of tubing in vertical well =158kg

Q: ugh a 1.0 in diameter pipe is 3 GPM with a pressure drop of 5 PSI. What would the pressure drop be…

A: Givend1=1inQ=3GPM∆P1=5psid2=1.5in

Q: Industrial pipes Do the guides allow movement of a pipe only in two directions (in a plane)?

A: The objective of the question is to understand the movement of a pipe in a guide in terms of…

Q: At a flow rate of 10 LPM, what will gonna happen if the pressure drops over 90 seconds from 0.657…

A: The flow rate given asthe time taken, pressure drop, the given pressure,

Q: hich of the following is turbulent flow according to Reynolds number for pipe? a. Re is less…

Q: What is the pipe velocity at point 12 Given the specific gravity of pink liquid S=3.9 and height…

A: Given Height, h = 0.4 m

Q: Convert 50 GPM to ft/s in a 4" Sch 40 pipe

A: Given data: V˙=50 GPMPipe=4'' schedule 40 pipe Need to Convert 50 GPM to ft/s.

Q: A 0.10-inch-diameter cappillary tube is filled with water at a certain temperature. The surface…

A: The value of capillary rise is calculated by using capillary rise formula, before putting values in…

Q: Water at 60F is flowing through a 3-inch inside diameter smooth horizontal pipe. If the Reynolds…

Q: main tempen ber he correct r

A: given:d=0.1insurface tension T=0.005lb/ft

Q: If the pressure difference between points 1 and 2 is 25 psi, what will be the flow rate? The pipes…

A: Given:

Q: Third Experiment - Compound Epicyclic Gear Driver pulley at gear set 2: Stationary gear = ring gear…

Q: For diameter of the pipe at 女 (a pered pipe as shown below, what is a )ス= ゴm üi) l-3m Lengih of the…

Q: What level h must be maintained in Fig. to deliver afl ow rate of 0.015 ft3/s through the 1/2-in…

A: Given data: For Water at temperature 20 degrees Celcius Flow rate = 0.015 ft3/s…

Q: b) A truck of total mass 18tonne descends a hill with a gradient of 1 in 14, i.e. a vertical…

A: Given thatm=18tonnes=18×103kggradient=1 in 14θ=14°P=900ND=112m

Q: An 80 mm schedule 40 steel pipe is 1800 m long and carries a lubricating oil between 2 points A and…

A: As per guidelines we need to answer only first question

Q: The pressure through a section of pipe is 21 PSI and the velocity of the fluid is 1 ft/sec. If the…

A: given data; pressure at section 1st (P1)=21PSI=144789.903pavelocity at section…

Question

8.61
cally through a 200-ft-long, 1.0-in.-diameter drawn tubing at a
rate of 0.060 ft'/s if the pressures at the inlet and outlet are the
same?
What horsepower is added to water to pump it verti-
Pump

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 2. Water at 150°F is pumped at the rate of 60 gal/min from a reservoir at atmospheric pressure. The gauge pressure at the end of the discharge line is 42 psi. The discharge point is 12 ft above the level is the reservoir and the suction line is 6 ft above the level of the reservoir. The discharge line is a 1 ½ in. nominal dimeter steel pipe with a schedule number of 80. The pressure drop due to friction in the suction line is known to be 0.8 psi, and that in the discharge line is 7.2 psi. The mechanical efficiency of the pump is 70%. Calculate (a) the developed head of the pump and (b) the total power input. (c) If the pump manufacturer specifies a required NPSH of 8 ft, will the pump be suitable for this service?
3. Calculate the Reynolds number, Re for water flow in a circular pipe. The diameter of the pipe is 50 mm, the density of water is 998 kg/m', the volumetric oil flowrate is 720 L'min, and the dynamic viscosity of water is 1.2 centipoise
Water at 60F is flowing through a 3-inch inside diameter smooth horizontal pipe. If the Reynolds number is 353,000. Calculate the ratio of maximum velocity to average velocity. (1.18)
The pressure through a section of pipe is 23 PSI and the velocity of the fluid is 3 ft/sec. If the velocity was increased to 5 ft/sec, what would the pressure drop be?
a pipe reducer with the pressure at A and B is 345kPa and 290kPa. the diameter at A and B is 50mm and 25mm. estimate the total head at point A and B?
Example: What is the pressure at the center of the pipe B?
What must the gauge pressure p be at A if the volume flow rate out of the pipe at point B is 0.0800 m^3/s?
Water in a constant diameter pipe is at 15m on the inlet the pipe leads to the tank situated at a height of 10m, if the total head losses are 8m and the pip inlet and outlet are exposed to the environment and the mass flow remains constant; Chose one of the following: A. no pump is required to ensure water flows to the tank B. none of the above C. a pump needs to ensure water flows to the tank D. the water will flow through gravity to the tank
A pressurized tank and piping system are shown in the figure. The tank pressure is maintained at 175 kPa. The line is made of 12 m of 1 std type M copper tubing and it conveys gasoline (octane). What is the expected flow rate through the line? All fittings are soldered (same as flanged) and regular. 4 m 175 kPa 1 m
The pressure loss through the pipe and the minimum power required to overcome the resistance to flow.
What is the minimum duct size needed to move 200 cu ft per minute andmaintain duct velocity below 800 feet per minute?
Problem 5- Two reservoirs are connected by 198ft of 2-in diameter tubing. What is the flow rate when the difference in elevation is 50ft? (v= .001 ft²/s)