In the following problem on regenerative hydraulic circuits, you're given the scenario:A pump's flow rate is 10 gallons per minute (gpm). The piston diameter is 7 inches, and the rod diameter is 5 inches (indicating it's not a 2:1 cylinder). Your tasks are to:1. Calculate the extension speed in inches per minute (in/min).2. Determine the oil flow rates at points A and B in gpm. - Note: 1 gallon is equivalent to 231 cubic inches.**Diagram Explanation:**The diagram illustrates a hydraulic circuit featuring:- **Pump (PF):** Positioned centrally, it circulates hydraulic fluid.- **Piston and cylinder assembly:** Located at the top right, with two sections labeled A and B indicating different fluid pathways.- **Arrows:** Indicate the direction of the fluid flow.The diagram’s representation of the circuit isn’t equipped to function as a regenerative circuit. Your challenge is to identify and specify essential modifications required to enable practical application of the regenerative circuit.

given data; ⇒flow rate (Q)=10gpm=6.309*10-5m3/s⇒piston diamter (d1)=7 in=0.1778m⇒rod diamter(d2)=5…

Answered: 8. In the regenerative circuit shown…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For Questions 3 to 5 A certain centrifugal pump was tested and its performance curves can be approximated as follows: H = 340 - 1.2(Q^2), in feet BP = (0.0521Q^3) + (1.250^2)+(11.042Q) + 134.5, in horsepower where Q is in ft^3/s. Question 3 If a single pump is used to deliver water of a system which requires a total of 8 ft^3/s, what is the efficiency of the pump (in %)? Take the specific weight of water to be 62.4 lbf/ft^3. Round your answer to 2 decimal places.
For a 6.25-inch Model 4075 pump operated at 1160 rpm, if 450 GPM of water is to be delivered, what will be the estimated pump head in ft? HEAD IN FEET 30 25 0 0 0 10 O 6 ft 7.25" (184mm) 20 7.00" (178mm). 6.75" (171mm). 6.50" (165mm)] 15 6.25" (159mm). 5 O 16 ft O 20 ft O 12 ft aco® L/SEC 5 OT 10 Model 4075 FI & CI Series 15 -6-6 ⁰ dº 20 ANA 888 778 25 REQUIRED NPSH do 1160 RPM November 1, 2010 K ・dº- [M 90 do 30 8800 81 1HP(.75KW) DeJ kin do 60% 35 do 50 Curve no. 2175 Min. Imp. Dia. 6.25" Size 5 x 4 x 7.0 40 45 3HP(2.2KW), 2HP(1 5KW) 5HP(1 1KW)> CURVES BASED ON CLEAR WATER WITH SPECIFIC GRAVITY OF 1.0 L 75 150 225 300 375 450 525 600 675 FLOW IN GALLONS PER MINUTE NOWONG FEET 15 12 7 6 2 1 NPSH 758 50 5 HEAD IN METERS 45 586888 KPO 60 40 20 10 LO HEAD IN KILOPASCALS
Show in Figure 1 is the water flow system. The velocity head difference is . Volume flow rate is . The heights are and , respectively. The power output from the motor is , . The energy added by the pump is . The energy loss between point 1 and 2 is . Calculate 4) the pressure head difference in meter_________ m
F-m question. Provide right answer
### Develop a conclusion of a piping design report for the choice of a pump, based on the calculated parameters of flow Q = 10 l/s, power of 10kw taking into account that the head of 60 mca adopted was higher than that calculated for safety, and that the pump was chosen through the WebCAPS catalogue of the company GRUNDFOS. The pump chosen was the GRUNDFOS CR 32-3 A-F-A-E-HQQE
A UMC 50-80 circulator is operating at 1750 RPM. Flow is 50 GPM. Feet of head (friction) is 19 ft. Brake horsepower is 0.40. RPM decreases to 60% of maximum. No other changes occur to the system. What is the new GPM?
Is there a flaw in the pipeline design as shown in Flgure 4 ? (select one): (A) The strainer and foot valve should not be used as the combination may cause cavitation. (B) The foot valve should not be used as it may cause cavitation. (C) The pump should be placed at a higher elevation to prevent cavitation from occurring. (D) The gate valve should not be placed on the suction side of the pump as it may cause cavitation. (E) The intake is not placed deep enough below the water surface of the river as it may cause cavitation. (F) None Elevation 180 m- 450 All of Steel Pipe Diameter 250mm· Smooth Bend B Gate Valve- (wide open) River Elevation -Pump at Elevation 125 m 120 m Smooth Bend Sump -Strainer and foot valve at 115m Figure 4

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

8. In the regenerative circuit shown below, the pump's flow rate is 10 gpm. If the piston diameter is 7 in and the rod diameter is 5 in (not a 2:1 cylinder), calculate the extension speed in in/min. Also calculate the oil flow rate at points A and B in gpm. (recall 1 gal = 231 in") B PF