A horizontal 154 mm diameter pipe gradually reduces its section to 53 diameter, subsequently enlarging into 154 mm section. The pressure in the 154-mm pipe at a point just before entering the reducing section is 141 kPa and in the 53 mm section at the end of the reducer, the pressure is 73 kPa. If 627 mm of head is lost between the points where the pressure are known compute the rate of flow in L/s of water through the pipe.

Q: asoline at 77°F flows from a pressurized upper tank to a vented lower tank as shown in the figure…

A: Givenh2=52.8ftTemp=77°Fρgasoline=45lb/ft3

Q: Show the step by step solution. Thank you. 3. A pump draws water from reservoir A and lifts it to…

A:

Q: A pump draws water from reservoir A and lifts it to reservoir B as shown in figure 4. Elev. of water…

A: Given:-

Q: A horizontal 150 mm diameter pipe gradually reduces its section to 50 mm diameter, subsequently…

A: Bernoulli's principle states that the flow energy of liquid before entering a section will be equal…

Q: 3. In the following system, the flow rate of Q= 400 lt / s is transmitted from the A chamber to the…

A:

Q: The diameter of the pipe at the larger end is 0.50 cm and at the smaller end is 0.20 cm, the larger…

A: Larger end: D1= 0.50 cmZ1= 7 mV1= 1.2 m/sP1= 5200 kN/m2 Smaller end: D2= 0.20 cmZ2= 3 m   To find:…

Q: Water flows through a reducer in a pipe as shown. The pressure at A is equal to 345 kPa and the…

A: GIVEN DATA - PA=345KPa    dA=150mm PB=325KPa    dB=60mm WE HAVE TO CALCULATE FLOW RATE

Q: Figure shows a portion of a fire protection system in which a pump draws water at 60°F (v =1.21…

A: To find: The required height h of the water level in the tank to maintain the pressure 5 psig at…

Q: Gate Vale-Half Open 4" Sch40 Globe Vale-Half Open 8 m 2" Sch40 2 m 2 m 10 m 2 m 5 m 10 m 450

A: Friction loss in the pipe is given by  Darcy Weisbach formula   hf=4fLV22gd   f = friction factor L=…

Q: A horizontal 150 mm diameter pipe gradually reduces its section to 55 diameter, subsequently…

A:

Q: QI) Oil of specific gravity sg = 0.8 is drawn into the pump, the pressure at A is -20 kpa and at B…

A: Fluid is a state of matter which deforms continuously on the application of force externally,…

Q: Problem 5: Given a Crucible with a base diameter (Din)of 8 mm and the length (L) of the attached…

A:

Q: . The tank is being filled by a faucet located at the top at a rate of 15L/s. It also has a 20 mm…

A:

Q: Flow Rate: 5305 Lis ORuler Speed Presure Units O Metrie O English 101.302 kPa Friction OFlux meter…

A:

Q: The velocity of the liquid flowing through the rusty iron pipe having a 150 mm diameter is 2.5 m/s.…

A:

Q: flow rate of water in the pipe which is con ed to tank B is the flow rate in the other two pipes and…

A:

Q: The pressure through a section of pipe is 21 PSI and the velocity of the fluid is 1 ft/sec. If the…

A: given data; pressure at section 1st (P1)=21PSI=144789.903pavelocity at section…

Q: 6.5 BELLOWS 8100mm The horizontal elbow is joined by bellows to the rest of the piping system and it…

A: NOTE: According to Bartleyby's policy we shall answer only one question at a time so kindly repost…

Q: 1. A siphon has an uniform circular section of 70 mm diameter and consists of a bent pipe with its…

A: for answers apply bernollis equation between A and C for Vc and for Pressure at B apply between A…

Q: pump is delivering hydraulic oil with a specific gravity of 0.85 at a rate of 75 L/min to a tank…

A:

Q: Water is flowing from A to B in a 4-in schedule 40 steel pipe. Point B is 6 m higher than point A…

A: Given,  Diameter of the Pipe , D = 4 inch  = 0.1016 m . Elevation of point B , above A , h = 6 m…

Q: A pump at an elevation of 300m is pumping 0.05 m³/s of water through 2.4 km of 150-mm pipe to a…

A:

Q: Water enters through a 23.616 inches diameter pipe under a pressure of 14 kPa. It leaves through a…

A: Given data:-diameter at section 1-1, d1=23.616inches=0.6m⇒area of cross-section at section 1-1,…

Q: Water at 20 Celcius degrees is pumped from a large reservoir through a pipe system which has a…

A: Given: The diameter of the pipe, d = 79 mm The length of the pipe, L = 13 m The mass flow rate of…

Q: 3. A pipe of diameter 400 mm carries water at a velocity of 25 m/s. The pressures at the points A…

A:

Q: 2. An inclined venturi tube containing water has an inlet of 300 mm diameter and a throat of 150 mm…

A:

Q: 1.Find the diameter of a pipe of length 3000 m when the rate of flow of water through the pipe is…

A:

Q: A vertical pipe is shown in figure 1 below. The pipe tapers from 50 mm in diameter to 25 mm in…

A:

Q: Q2/ A pipe with a radius of 15 mm is attached to a garden hose with a nozzle. If the velocity of…

A:

Q: A pitot-static tube placed in the centre of a 300 mm pipe line has one orifice pointing upstream and…

A: Data given-  d = 300 mm = 0.3 m  Mean velocity = 0.8 × central velocity  Cv = 0.98  Pressure…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.