A horizontal 150 mm diameter pipe gradually reduces its section to 50 mm diameter, subsequently enlarging into 150 mm section. The pressure in the 150-mm pipe at a point just before entering the reducing section is 140 kPa and in the 50 mm section at the end of the reducer, the pressure is 70 kPa. If 600 mm of head is lost between the points where the pressures are known, compute the rate of flow of water through the pipe.

Q: 2 in tube schedule 40 flow 24 in 4 in tube schedule 40 - 6 in water h

A: given; lets take pressure at A=PAlets take pressure at B=PB⇒diameter at A (dA)=4in=0.1016m⇒diameter…

Q: asoline at 77°F flows from a pressurized upper tank to a vented lower tank as shown in the figure…

A: Givenh2=52.8ftTemp=77°Fρgasoline=45lb/ft3

Q: Two reservoirs with top surfaces placed on the flat ground and connected with each other with a…

A: Write the given data with suitable variables. z1=10 mz2=30 mhf=40 m

Q: A vertical pipe is shown in figure 1 below. The pipe tapers from 50 mm in diameter to 25 mm in…

A: Given, Q=2 L/min=2×10-360 m3/s=3.333×10-5 m3/s d1=50 mmd2=25 mm hl=kv22-v122g z1-z2=1.5 m

Q: termine the discharg

A: for the other end to open to the atmosphere the net headloss in the pipe should be equal to 3m this…

Q: Water is flowing through a horizontal pipe of diameter 200 mm at a velocity of 3 m/s. A circular…

A: We have, Diameter, d=200 mm=0.2 m,     V=3 m/s Diameter of circular plate, d1=150 mm=0.15 m (as…

Q: 5. A nozzle that discharges a 60-mm-diameter water jet into the air is on the right end of a…

A: To determine:the magnitude and direction of the resultant axial force.Given:The outlet diameter of…

Q: As seen in Figure 3 below, the water from the tank 1 is pumped to the tank 2 with a flow rate of…

A:

Q: Water with flow rate of 12 lps from ground level is delivered to upper levels using the 50-mm…

A: Given,  The water flow rate, Q = 12 L/s The diameter of pipe, d = 50 mm The angle between inlet and…

Q: Assume the water in the first tank maintains its height and pressure. The valve is opened and after…

A: Solution: Given Data: P=200 kPaρ=1000 kg/m3D=5 cmPatm=100 kPa   To Find: Mass flow rate through the…

Q: Water at 35 degrees Celsius is flowing through a smooth pipe with a length of 95m and a diameter of…

A: Answer: (a) The friction head developed in the flow: 0.06589 m. (b) The pressure reduced due to…

Q: A small, high pressure water jet can be used for cutting various materials. A jet with a speed of…

A: For the solution refer below images.

Q: 3. Three pipes of diameters 0.4m, 0.2m and 0.3m of lengths of 400m, 200m, and 300m, respectively,…

A:

Q: Problem 2: Find the volume flow rate of water exiting from the tank shown in the figure below. The…

A: Find the volume flow rate.

Q: Water is filled into a circular tank (inner diameter 1 m) from two inlet pipes as shown. The…

A: Inner diameter of the tank, Volumetric flow rate at inlet 1, Let the volumetric flow rate at inlet 2…

Q: ● Compute the time needed for the cylinder position to retract from the maximum position 1m to…

A:

Q: Water enters a motor through a 500-mm-diameter pipe under a pressure of 15 kPa. It leaves through a…

A:

Q: calculate the power (kW) delivered by the pump

A: Need to calculate the power.

Q: A vented 50-gallon cylindrical reservoir (diameter = 18 inches) is used to supply ambient…

A: Given: Here is the given image, To determine: The required height (m) of water in the reservoir…

Q: 1a. Water flows into a tee fitting at a flow rate of 0.02 m3 /s. A pipe is connected to B. The…

A:

Q: 5. As shown in Figure 4, the water to drive a Pelton wheel is supplied through a pipe from a lake as…

A:

Q: The piping arrangement shown delivers a jet of water at location C. Water enters the pipe from ne…

A: given minor coefficient bwtween A and B , KAB=7minor coefficient bwtween B and C , KBC=3Diameter of…

Q: QUESTION 4 A vertical pipe is shown in figure 1 below. The pipe tapers from 50 mm in diameter to 25…

A:

Q: QI) Oil of specific gravity sg = 0.8 is drawn into the pump, the pressure at A is -20 kpa and at B…

A: Fluid is a state of matter which deforms continuously on the application of force externally,…

Q: Problem 5: Given a Crucible with a base diameter (Din)of 8 mm and the length (L) of the attached…

A:

Q: Q1) Oil of specific gravity s.g = 0.8 is drawn into the pump, the pressure at A is -20 kpa and at B…

A: Let Q =Discharge =0.07m3/s dB= Diameter of Pipe =80mm A =Area of pipe =0.005m2 g =Acceleration due…

Q: The diameter of a pipe line is 6 inch at A and 18 inch at B. A is 11 ft lower than B. If the…

A: GivendA=6in=0.1524 mdB=18in =0.4572mZ1=11ft=3.3528mPA=10lb/in2 =68.947kPaPB=7lb/in2=48.263…

Q: The piping shown in the figure is a parallel-pipe system carrying water at normal temperature.…

A: Given: Q=0.35 m3/sPipe A→lA=4000 m, dA=0.3 mPipe B→lB=2500 m, dB=0.35 mPipe C→lC=3000 m, dC=0.2 m

Q: Two tanks connected by three pipes in series are shown in Figure 2. The lengths of these pipes are…

A:

Q: In the syringe shown below, the drug had a density of 900 kg/m3 and flows through the needed at 0.4…

A:

Q: The velocity of the liquid flowing through the rusty iron pipe having a 150 mm diameter is 2.5 m/s.…

A:

Q: A 500 mm diameter pipe gradually reduces to 20 mm diameter and the gradually enlarge to its original…

A: Given volume flow rate is Q=0.08m3/s 1. The velocity at point 1 is - Q=Av0.08 = π40.52v1v1=0.41 m/s

Q: Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of…

A: Given  Rate of flow of water = 7L/s 5in schedule 40 steel pipe. 2 fittings of 90o ell standard long…

Q: Fluid Mechanics Problem

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.