A L = 5ft W = 120 lbs. B If Ø = 38° 45', what is the bearing reaction on the pivot an instant after being released from the given position? A) 120.5 lb B) 135.87 lb C) 153.87 lb D) 180.25 lb What is the bearing reaction just before impact at B if the velocity of the hammer is 7.5 ft per second? A) 161.93 lb B) 176.54 lb C) 180.78 lb D) 192.54 lb

A L = 5ft W = 120 lbs. B If Ø = 38° 45', what is the bearing reaction on the pivot an instant after being released from the given position? A) 120.5 lb B) 135.87 lb C) 153.87 lb D) 180.25 lb What is the bearing reaction just before impact at B if the velocity of the hammer is 7.5 ft per second? A) 161.93 lb B) 176.54 lb C) 180.78 lb D) 192.54 lb

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

View Policies Current Attempt in Progress A steel [E = 200 GPa] rod with a circular cross section is 18 m long. Determine the minimum diameter required if the rod must transmit a tensile force of 340 kN without exceeding an allowable stress of 200 MPa or stretching more than 14 mm. drod i mm
3 The piece of plastic is originally rectangular. Calculate the shear strain Yxy at corners A and B if the plastic distorts as shown by the dashed lines. 2 mm 300 mm 2 mm D -400 mm- mm, B A 4 mm 72 mm 3 mm X
Example: Determine the resultant of the three tension forces acting on the eye bolt. 30 4 kN 20 KN 8 kN
A flanged bolt coupling consists of 8 steel bolts to be distributed equally into two bolt circles as shown in the figure. The coupling is to transfer torque of 3.5 kN-m, what should be the minimum diameter to be used without exceeding the bolt shearing capacity of 63 MPa? 200 mm
The rectangular plate (L,xL,) given below is installed between two rigid walls and is deformed as shown by dashed lines. Determine the shear strain y and Yxy at point A. Use the table given below and your student ID to find the values of L, L, a, and b. L2 A b. L. b L, (mm) (mm) (mm) 150 200.0 3.0 3.0
Four gears are attached to a circular shaft and transmit the torgues shown in the figure. The allowable shear stress in the shaft is 20,000 psi. 8000 lb-in. 19,000 lb-in. 4000 lb-in. A 7000 lb-in. B D (a) What is the required diameter d of the shaft (in inches) if it has a solid cross section? in. (b) What is the required outside diameter d (in inches) if the shaft is hollow with an inside diameter of 1.8 in.? in.
Two vertical rods AB (A36 steel, E = 200 GPA) and CD (red brass, E = 101 GPA) support a rigid bar AC which is loaded at E. In the current configuration workers in the factory have noticed the horizontal bar AC rotates slightly once the load in E is applied. This is causing problems and needs to be addressed. Your supervisor has asked you to first verify that this rotation is occurring and calculate its magnitude. Then determine the new location for the load application point E such that this rotation can be eliminated.
Discuss the different sources of size effect. Describe energetic size effect in fractureusing two different sizes of a plate with a center notch. Explain the significance of platethickness.
If the load that can be supported by the given support structure is unknown, calculate the maximum load that the structure can support by considering the maximum allowable stress for section BC is 155.8 MPa. provide your answer in kN with precision to two decimal points. 600 mm Answer: 50 mm d-20 mm 800 mm- B
D Question 7 A 2-ft rod with a modulus of elasticity of 8840 ksi, is subjected to a tensile force of 1000 lb and has an elongation of 0.009 in. The initial radius of the material is most nearly? O 0.94 in O 0.10 in O 0.31 in O 2.83 in
As a construction engineer, you are asked to evaluate the maximum allowable vertical shear Vmax that may act on the hollow stainless-steel beam having a rectangular cross section as shown in Figure Q4. Discuss the effect of geometry on the shear stress developed in the beam | 20 mm y 350 mm V 10 mm- -10 mm 1 30 mm E 200 mm
Problem 4: A flanged bolt coupling consists of eight 10-mmdiameter steel 200 mm bolts on a bolt circle 400 mm in diameter, and six 10-mm- diameter steel bolts on a concentric bolt circle 300 mm in ↑150 mm diameter, as shown in Figure. What torque can be applied without exceeding a shearing stress of 60 MPa in the bolts? Determine the number of 10-mm-diameter steel bolts that must be used on the 400- mm bolt circle of the coupling described in Problem 3 to increase the torque capacity to 14 kN-m