Answered: An aluminum rod 20 mm in diameter and 5…

An aluminum rod 20 mm in diameter and 5 m long is subjected to an axial tensile load of 50 kN compute strain if E for rod is 70x103 Mpa. O a.5,67x103 Ob.2.87x10-3 Oc.3.27x103 O d.27x103

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.3P: A tensile test was performed on a metal specimen having a circular cross section with a diameter 0....

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
A round aluminum alloy rod has a diameter of 12.5 mm and 1 m length. Its ultimate strength is 155 MPa and its modulus of elasticity is 70 GPa. Determine the maximum permissible axial load that may be applied if the total elongation of the member is not to exceed 2 mm. Calculate the diameter change if Poisson’s ratio=0.35.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m 10KN 0.8m 0.4m 5KN 0.6m What is the deformation 8Rc in mm? Al 20KN A=800 mm? A=1,200 mm²
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.71 in and an elastic modulus of 2050 ksi. Bar (2) has a cross-sectional area of 1.019 in? and an elastic modulus of 3910 ksi. Assume L-20 in. Lyn47 in. Q-6 kips. P-3.6 kips, and R-13.2 kips. Determine the horizontal deflection of end Crelative to end A. (1) (2) Answer: UCIA - in.
Find the lightest S-shape for the beam shown if the working stress in bending is 175 MPa. What is the maximum bending stress in the beam selected? 50 kN/m 4 m -2.4 m· -x X- TABLE B-3 Properties of I-Beam Sections (S-Shapes): SI Units Flange Axis Y-Y Web X-X spxy Mass Area Width ıdə (wu) Thickness thickness Pl1 = S (10³ mm³) yli^ = 4 (10° mm*) (u) 27.7 27.7 22.1 Designation (10° mm*) (ww) 20.3 (ww) 38.9 („ww) (ww) (ww) 081 158 006 77 622 622 204 1 320 1 220 081 x 019S 4 230 240 34.5 338 × 158 x 149 x 134 007 184 15.7 3930 3 260 247 O'ZE 19.7 320 001 07 6'6E 32.3 006 81 00 I 15 200 149 6'81 15.9 166 937 677 234 019 215 134 181 22.1 090 € 2870 019 18.6 205 33.0 611 22.1 12.7 874 241 17.5 197 61I x 34.0 019 S510 × 143 143 18 200 16300 14 200 12 500 91S 91S 183 23.4 23.4 20.2 20.3 16.8 S69 653 2 700 20.8 228 x 128 x 112 × 98.2 128 112 33.8 34.5 29.5 179 961 2 540 007 194 19.4 80s 508 216 152 162 16.1 533 001 7 1950 12.3 98.2 20.2 12.8 495 6SI 11.4 144 30.2 661 S460 × 104 104 13 200 457 6SI…
An aluminum rod is rigidly attached between a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximun value of P that will not exceed a stress in steel of 169Mpa, in aluminum of 98Mpa and in bronze of 111Mpa.
PLS PROVIDE COMPLETE SOLUTION THANKS
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
Beam CX is subjected to a loading condition as shown in the figure. What will be the (a) the maximum tensile stress and (b) the maximum compressive stress in the Beam CX if its cross section is a T section with the given dimensions.