The frame shown in Figure below is made of a beam, for which the Plastic moment is Mp.(i) Sketch ALL possible modes of collapse showing clearly the locations of plastic hinges in eachmode,(ii) calculate ALL corresponding magnitudes of collapse loads and(iii) finally determine the magnitude of the critical load P which will cause the frame to collapse,comment on the result.Assume L = 5.0 m.2P2L3PLL

Answered: Image /qna-images/answer/4a4de353-5a34-4c8c-9cd2-c1fc95ba96ff.jpg

Answered: (i) Sketch ALL possible modes of…

Engineering

Civil Engineering

(i) Sketch ALL possible modes of collapse showing clearly the locations of plastic hinges in each modo

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Another way of testing flexure strength is by quarter point loading as shown. The sample section is 150mm x 150mm. If both P = 50,000N, what is the stress at failure at point O? %3D P 200mm 200mm 200mm Point O 600mm R1 |R2
A beam with varying load is shown at the figure below. If the beam properties are given, what is the final stress at top of the beam at midspan where total losses of the prestressing force is 21% (MPa)
1. Determine the maximum tensile and compressive bending stresses in the beam shown. 6 kN A B C 120 1.0 m 1.2 m 2 kN -| 4090→ 40 |- Dimensions in mm 2. Find the lightest S-shape for the beam shown if the working stress in bending is 120 MPa. What is the maximum bending stress in the beam selected? 40 kN/m 4 m - 2.4 m 3. For the beam shown in the figure, find the shear stress at a point 30 mm above the bottom of the beam at section C. 50 mm | 14 kN E1.5 m – 3 m 100 mm I = 19.3 × 106 mmª B C A NA 62.5 mm 50 mm 2 m 100 mm 4. The simply supported wood beam, fabricated by gluing together four wooden boards, carries the three concentrated forces. The working bending and shear stresses for the wood are 1000 psi and 600 psi, respectively. Determine the largest allowable value of the force P. P 0.5 in. → -8 in.→+ 0.5 in. P 2 in. 2 ft -4 ft-+ 4 ft→ 2 ft 6 in. $2 in. SAP
A simply supported beam is carrying a uniform load. If the beam properties are given below, what is the final stress at bottom of the beam section at midspan where the total losses of the prestressing force is 23% (MPa) Properties: Beam width = 285 mm Beam height = 475 mm Uniform load = 9.1 kN/m Span of the beam = 13 m Prestressing force 469 kN eccentricity = 104 mm %3D %3D %3D %3D
I need the answer as soon as possible
View Policies Show Attempt History Current Attempt in Progress Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are $x = 12 ksi, Sy = 33 ksi, and Sxy= 17 ksi. (a) Determine the principal stresses (op1 > 2) and the maximum in-plane shear stress Tmax acting at the point. (b) Find the smallest rotation angle 0, (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) T Sxy Sx D
Determine the stress concentration factor for the beam shown below that has a fillet to the larger diameter knowing that: Material modulus of elasticity = 208 GPa Diameter D = 75 mm Length L = 550 mm Normal strain at the base of the fillet (from strain gage reading on the top of the beam) = 0.0005 Load P = 5.00 kN Moment of inertia for a circular section is %3D %3D R* /4
In the following beam system, the beam is subjected to uniform distributed load W = 25 lb /in. Assume a = 90-inch, b = 130-inch, C = 40 inch and d = 50 inch a) Determine the resultant force produced at the pin C for the distributed load, W b) What is the factor of safety that exists for pin C with respect to its fracture strength? assume that the pin at C fractures when the resultant force reaches a value 35000 lb.
Kindly answer correctly. Please show all the necessary steps. Thanks in advance.
For questions 7A and 7B, see figure 07 below. The cross section has the given properties, and the beam has the given loadings. The 5KNm and 10KN are located at third points. 7A. Determine the maximum compressive stress developed in the beam shown.
Please help me
%3D QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum beam as shown in the figure. (a) Calculate the maximum values of compressive and tensile normal stresses on the crss section. (b) Define the orientation of the neutral axis and draw on the cross-sectionç. M = 5 kN.m 30° 10 mm 40 mm 10 mm A-40 mm--r: 30 mm 30 mm 10 mm 10 mm