(a) In this simple frame-work, members have different lengths, cross-sectionalareas and materials, and are pin jointed.(i) Describe how you would develop thefinite element equation of equilibriumin global form indicating the appropriateboundary conditions.(iii) If the members were welded at the joints,would the truss elements still be suitablefor this problem? Give reasons.2F

Explanation to the answer is explained above

Answered: (a) In this simple frame-work, members…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A bolted joint consists of 40-mm thick AISI 1020 steel plate sandwiched between two 12-mm thick aluminum plates and compressed with a bolt and nut with no washers. The bolt is M14x 2, property class 5.8. (a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness. (c) Determine the stiffness of the members. (d) Determine the joint stiffness constant
Two (2) rods of the same material each has a diameter of 20mmare welded together to form a total length of 600mm If the rod has a strength of 15 MPa and the joint efficiency is 85%, what tensile load the rod can safely carry? If the rod is made of steel, what elongation is permissible under this condition?
Design a triple riveted butt joint with equal double cover plates (zig-zag riveting) is used for The longitudinal joint of boiler of D m internal diameter. The working steam pressure is P N/mm2 and the efficiency of the joint is B per cent. If the allowable working stresses for Plate are 120 Mpa in tension, 80 Mpa in shear and 180 Mpa in crushing and the allowable Working stresses for the rivet are 125 Mpa in tension, 84 Mpa in shear and 180 Mpa in Crushing. Design a double riveted lap joint with zig-zag riveting circumferential also. Checked the efficiency of longitudinal and circumferential joints. B=83 P=1.1 D=2.1
A 30-mm thick AISI 1020 steel plate is sandwiched between two 20-mm thick2024-T3 aluminum plates and compressed with a bolt and nut with no washers. The boltis M12 × 1.75, property class 9.8. Draw a sketch of the joint and,(a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness.(c) Determine the stiffness of the members and joint stiffness.
c. Determine critical load and critical stress for the column/axial member. Justify selection of the formulas for the calculationsInformation provided: i) Boundary/end conditions: In this instance, the column is assumed to be fixed at both ends, simulating conditions where the column is integrally connected to the floor slabs above and below, a common condition in many mechanical design contexts. ii) External axial load: Assuming the column supports a floor with a uniformly distributed load, we've calculated the total axial load on the column to be 453.589 kN. iii) Properties of the column: The cylindrical column is composed of steel, a commonly used material with a known Young's modulus (E) of approximately 200 GPa. The steel has a yield stress of around 250 MPa and ultimate stress near 400 MPa. The diameter (d) of the column is 0.3048 m, providing a cross-sectional area (A) of π*(d/2)² = 0.073 m².
Hi, I have been given this pin-jointed frame analysis to solve (see pictures of the structure attached). Can you help me answer all the questions below? Especially the one about the bending moment and shear force. The Figure 2 attached is a simplified structure to undertake a structural analysis on a concept design for a low cost stroller/buggy for children. The buggy consists of a number of metal sections that are pin-jointed together. The buggy is designed to accommodate a child of mass no more than 20 kg, sat on the seat which is supported at four points (Fc) on the frame of the buggy. Assume that the weight of the child is equally distributed across all of the points indicated on Figure 2 as Fc. Assume that there are no additional forces applied to the handle of the buggy, that the buggy is static (stationary) and that the buggy, and the elements of the frame have no mass. At points A and G, there are roll supports. At Points B, F and D there are the pin supports. I am required…
4. Determine the design stress for bolts in a cylinder cover where the load is fluctuating due to gas pressure. The maximum load on the bolt is 50 kN and the minimum is 30 kN. The load is unpredict- able and factor of safety is 3. The surface of the bolt is hot rolled and the suface finish factor is 0.9. During a simple tension test and rotating beam test on ductile materials (40 C 8 steel annealed), the following results were obtained : Diameter of specimen =12.5 mm; Yield strength= 240 MPa; Ultimate strength= 450 MPa; Endurance limit = 180 MPa. [Ans. 65.4 MPa]
Y- young’s modulus
Example 4-3 The two C12 x 30s shown in Fig. 4.2 have been selected to support a dead tensile working load of 120 k and a 240-k live tensile working load. The member is 30 ft long. consists of A36 steel, and has one line of three 7/8-in bolts in each channel flange 3 in on center. Using the AISC Specification, determine whether the member is satisfactory and design the necessary tie plates. Assume centers of bolt holes are 1.75 in from the backs of the channels. Solution. Using C12 x 30s (A, 8.81 in? cach, t, 0.501 in, I, 162 in' each, 1, 5.12 in each,y axis 0.674 in from back of C,r, = 0.762 in) 5.326 in 0.674 in cg. of C -x 1200 in 2-C12 x 30s (A = 881 in' each) Ln g-1 in 8} in- 12 in (a) Tie plate Length of tie plate Width of tie plate FIGURE 4.2 Built-up section for Example 4-3. (b)
MACHINE DESIGN TOPIC A short compression member with Do = 2Di is tosupport a dead load of 25 tons. The material isto be 4130 steel, WQT 1100 F. Calculate theoutside and inside diameters in terms of incheson the basis of (a) yield strength, (b) ultimatestrength.*For 4130 steel, WQT 1100 FSu = 127 ksiSy = 114 ksi*Use the following Safety FactorsNu = 4Ny = 2
V Question Completion Status: 1.805 QUESTION 3 A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, Su-345 MPa) for the C-frame material. State whether true/false. Under the loading conditions, failure happens 18 mm 38 mm 13 kN 10 mm -90 mm 25 mm A A 10 mm O True O False AurCT ION A Click Save and Submit to save and submit. Click Save All Answers to save all answers. Save A re to search
Stuck need help! Problem is attached. please view attachment before answering. Really struggling with this concept. Please show all work so I can better understand ! Thank you so much.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS