A glue-laminated timber beam is reinforced by carbon fiber reinforced plastic (CFRP) material bonded to its bottom surface. The cross section of the composite beam is shown in figure below. The elastic modulus of the wood is E= 12 GPa and the elastic modulus of the CFRP is 112 GPa. The simply supported beam spans L = 6 m and carries a concentrated load P=3.9 kN at midspan, see figure below. L/2 Answer: 9.3333 B L/2 C If b₁ = 89 mm and b₂ = 39 mm determine: a) the modular ratio n. Enter your answer to 4 decimal places. CFRP b₁ b₂ 250 mm 3 mm

A glue-laminated timber beam is reinforced by carbon fiber reinforced plastic (CFRP) material bonded to its bottom surface. The cross section of the composite beam is shown in figure below. The elastic modulus of the wood is E= 12 GPa and the elastic modulus of the CFRP is 112 GPa. The simply supported beam spans L = 6 m and carries a concentrated load P=3.9 kN at midspan, see figure below. L/2 Answer: 9.3333 B L/2 C If b₁ = 89 mm and b₂ = 39 mm determine: a) the modular ratio n. Enter your answer to 4 decimal places. CFRP b₁ b₂ 250 mm 3 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the figure, aluminum [E = 75 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a cross-sectional area of 330 mm² and link (2) has a cross-sectional area of 560 mm2. For an applied load of P = 37 kN, determine the rigid beam deflection vg at point B. Assume a = 1790 mm, b = 850 mm, L₁= 2420 mm, and L₂ = 4030 mm. L₁ (1) Answer: vg = i B b (2) mm. L2
A simply supported wood beam of rectangular cross section and span length 1.2 m carries a concentrated load P at midspan in addition to its own weight (see figure). The cross section has width 140 mm and height 240 mm. The weight density of the wood is 5,4 kN/m3Calculate the maximum permissible value of the load P if (a) the allowable bending stress is MPa and (b) the allowable shear stress is 0,8 MPa
A beam supports a point load of P=1700 lbf, at end A, and a distributed load from B to C of W=250 Lbf/in, as shown in the figure. The beam has a cross section where a=1pig and b= 3in. of this section, determine the minimum yield resistance that the beam material must have so that the design has a minimum safety factor n=3. Consider the maximum normal tensile stress. Explain step by step.
A horizontal beam AB with cross-seetional dimensions 4 ft 5 ft- b#0,75 in.)X KW#8.0 in. is supported by an inclined strut CD and carries a load P = 2700 lb at joint B (see figure part (a)]. The strut, which consists of two bars each of thickness 5b/8, is connected to the beam by a bolt passing through the three bars meeting at joint C Asee figure part (b)]. OB 3 ft (a) If the allowable shear stress in the bolt is 13,000 psi, what is the minimum required diameter d. of the bolt at C? (b) If the allowable bearing suess in the bolt is 19,000 psi, what is the minimum required diameter dmin of the bolt at C?
d) moment of inertia about the horizontal centroidal axis for transformed CFRP. Enter your answer in mm¹ to 2 decimal places.
5.8-6) A cantilever beam of length L = 2 m sup- ports a load P = 8.0 kN (see figure). The beam is made of wood with cross-sectional dimensions 120 mm X 200 mm. Calculate the shear stresses due to the load P at points located 25 mm, 50 mm, 75 mm, and 100 mm from the top surface of the beam. From these results, plot a graph showing the distribution of shear stresses from top to bottom of the beam. P = 8.0 kN 200 mm L = 2 m 120 mm PROBLEM 5.8-6
In the figure, aluminum [E = 75 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a cross-sectional area of 330 mm² and link (2) has a cross-sectional area of 560 mm2. For an applied load of P = 37 kN, determine the rigid beam deflection vg at point B. Assume a = 1790 mm, b = 850 mm, L₁= 2420 mm, and L₂ = 4030 mm. L₁ (1) Answer: vg = i B b (2) mm. L2
A composite beam is made of two brass [E =101 GPa] plates bonded to an aluminum [E =64 GPa] bar, as shown in Figure below. The beam is subjected to a bending moment of 2030 N-m acting about the z axis. Assume b=53 mm, d1=52 mm, d2 =11 mm, Determine: (a)the maximum bending stresses in the brass plates and the aluminum bar. (b) the stress in the brass at the joints where the two materials are bonded together.
A wood beam with a rectangular cross section(see figure) is simply supported on a span oflength L. The longitudinal axis of the beam is horizontal,and the cross section is tilted at an angle α.The load on the beam is a vertical uniform load ofintensity q acting through the centroid C.Determine the orientation of the neutral axisand calculate the maximum tensile stress σmax ifb = 80 mm, h =140 mm, L =1.75 m, α = 22.58, andq = 7.5 kN/m.
The cross section of a composite beam madeof aluminum and steel is shown in the figure. The moduliof elasticity are EAl = 75 GPa and Es =200 GPa.(a) Under the action of a bending moment that producesa maximum stress of 50 MPa in the aluminum,what is the maximum stress σs in the steel?(b) If the height of the beam remains at 120 mmand allowable stresses in steel and aluminum aredefined as 94 MPa and 40 MPa, respectively,what heights hAl and hs are required for aluminumand steel, respectively, so that both steeland aluminum reach their allowable stress valuesunder the maximum moment?
A steel beam, of lengths a=4 m and b=4 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q=0 kN/m to q=4.4 kN/m for AB span; and is constant with q= 4.4 kN/m for BC span. The Young's modulus of steel is 200 GPa. Ay, v 9 Part A a 5 mm 200 mm Figure Q.1 300 mm B b C X Calculate: a) the vertical support reaction in support A. When sketching FBD, set the positive directions of both reactions in the positive direction of yaxis. Enter your answer in kN to three decimal places.
3. 4 For the beams shown in the figure below, L = 2m, P = 5000N, E = 70 GPa, I = 2x10-4 mª (a) Determine the deflection and rotation angle in the middle point. (b) Find reaction force and moment in B. A L 2 P 77 L 2 B