A steel beam, of lengths a= 6 m and b = 3 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q=0 kN/m to q = 3.1 kN/m for AB span; and is constant with q=3.1 kN/m for BC span. The Young's modulus of steel is 200 GPa. Part A Calculate: A y, v a 5 mm 200 mm Figure Q.1 9 ÅB 300 mm b C 81 X

A steel beam, of lengths a= 6 m and b = 3 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q=0 kN/m to q = 3.1 kN/m for AB span; and is constant with q=3.1 kN/m for BC span. The Young's modulus of steel is 200 GPa. Part A Calculate: A y, v a 5 mm 200 mm Figure Q.1 9 ÅB 300 mm b C 81 X

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A wood beam with a rectangular cross section(see figure) is simply supported on a span oflength L. The longitudinal axis of the beam is horizontal,and the cross section is tilted at an angle α.The load on the beam is a vertical uniform load ofintensity q acting through the centroid C.Determine the orientation of the neutral axisand calculate the maximum tensile stress σmax ifb = 80 mm, h =140 mm, L =1.75 m, α = 22.58, andq = 7.5 kN/m.
A steel beam, of lengths a=4 m and b=4 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q=0 kN/m to q=4.4 kN/m for AB span; and is constant with q= 4.4 kN/m for BC span. The Young's modulus of steel is 200 GPa. Ay, v 9 Part A a 5 mm 200 mm Figure Q.1 300 mm B b C X Calculate: a) the vertical support reaction in support A. When sketching FBD, set the positive directions of both reactions in the positive direction of yaxis. Enter your answer in kN to three decimal places.
Question 2A rigid beam ABC is supported by pin at A and reinforced by a bar BD in order to sustain the uniform distributed load of 5 kN/m along the beam ABC in the direction shown in the Figure Q2.(a) Draw the free body diagram and determine the reaction forces at joint A(b) Determine the resultant force at joint A and its direction(c) Determine the internal loadings at section a--a
A steel beam, of lengths a = 5 m and b = 2 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q = 0 kN/m to q = 5 kN/m for AB span; and is constant with q = 5 kN/m for BC span. The Young’s modulus of steel is 200 GPa. Questions: 1. Calculate the vertical support reaction in support A. When sketching FBD, set the positive directions of both reactions in the positive direction of y axis. Enter your answer in kN to three decimal places. 2. Calculate the vertical support reaction in support B. Enter your answer in kN to two decimal places. 3. Calculate the value of the maximum bending moment in the beam. Enter your answer in kNm to three decimal places. Note: when deriving internal moment equations, use the following…
A wooden beam AB supporting two concentrated loads P has a rectangular cross section of width b = 100 mm and the height h = 150. The distance from each end of the beam to the nearest load is a = 0.5 m. the span kf the beam is 5 m. Determine the maximum permissible value P (in kN) if the allowable stress in bending is 11 MPa (for both tension and compression)
During construction of a highway bridge, the main girders are cantilevered outward from one pier toward the next (see figure). Each girder hasa cantilever length of 48 m and an I-shaped cross section with dimensions shown in the figure. The load on each girder (during construction) is assumed to be 9.5 kN/m, which includes the weight of the girder. Determine the maximum bending stress in a girder due to this load.
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 17 cm as width, 28 cm as depth and inner thickness as 2 cm is subjected to a point load of 7 N & 5 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 2 cm from the top. Take AC = 2 m & CD = 2 m. note ; Please solve number 3.4.5.6.7 i) Reaction force at B = 33.4N ii) Reaction Force at A = 18.6N iii) The distance from B at which the shear Force value changes from "-" to "+" = iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I = vi) Maximum bending stress = vii) Bending stress at 2 cm from the top =
The simply supported beam shown in Figure 1 (see next slide) spans a distance of L = 6 m and carries two concentrated loads P, which are applied at a distance of a = 1.5 m from the supports. The beam is fabricated by bolting a steel plate between two wood planks (see Figure 2). The wood planks each have dimensions of b = 30 mm and d = 240 mm. The steel plate has dimensions of t = 9.5 mm and d = 240 mm. The moduli of elasticity of the wood and the steel are 12.5 GPa and 200 GPa, respectively. a) Determine the maximum bending stresses produced in the wood planks and the steel plate if P = 8 kN. b) Assume that the allowable bending stresses of the wood and the steel are 8.25 MPa and 150 MPa, respectively. Determine the largest acceptable magnitude for concentrated loads P. (You may neglect the weight of the beam in your calculations.)
The beam AB, shown in Figure 1a, with length L = 4.5 m is subjected to a uniform distributed load w = 13 kN/m and a concentrated moment M = 18 kN.m applied at point B. The beam has a rectangular cross-section with height h = 183 mm, width b = 98 mm, and constant thickness t = 12.5 mm as shown in Figure 1b. Take E = 200 GPa. 1 Determine the slope at point B 2 Determine the vertical displacement at point B [
L1 PB 2 E2 L2 D2 Dimensions: L2 L1 D2 D1 17 mm 18 cm 23 cm 15 mm Problem Statement: The rod shown is subjected to loads of PR = 112 kN and Pe = 18 kN. Segments AB and BC have elastic moduli of E, = 206 GPa and E = 73 GPa. The rod has circular cross-sections, and the dimensions of the rod are given above. Find the overall change in length of the rod under this load. Assume: • The collar at B is rigid • Stress concentration effects may be neglected 2014 Michael Swanbom
A wooden beam (1) is reinforced with steel plates (2) rigidly attached to its top and bottom surfaces, as shown in the figure. Dimensions of the cross section are b₁ = 5.50 in., d,= 10.75 in., b₂ = 3.50 in., and d₂ = 0.55 in. The elastic moduli of the wood and steel are E₁ = 1, 250 ksi and E₂ = 30, 000 ksi, respectively. The allowable bending stresses of the wood and steel are 1200 psi and 19500 psi, respectively. Determine the largest concentrated vertical load that can be applied at midspan if a simply supported beam with this cross section spans 16.8 ft. by Jd₂ (1) 2- (2) P = (2) b₂ d₁ Td₂ eTextbook and Media: lb
The beam shown in the figure consists of a W360 x 79 structural steel wide-flange shape [E = 200 GPa; I = 225 × 106 mm¹]. For the loading shown, determine: (a) the reactions at A, B, and C. Enter a positive value for a reaction force that acts upward on the beam, or a negative value for a reaction force that acts downward. (b) the magnitude of the maximum bending stress in the beam. Enter a positive value for the magnitude. Note: Use the tabulated value for the section modulus S from Appendix B directly in the stress calculation. Although S is related to the area moment of inertia I and the cross-section depth d, due to round-off in the tabulated data for S, I, and d, a slightly different answer for the bending stress is obtained using S directly as compared to the result obtained in using I and d. Of course, performing the calculation using either S directly, or using I and d, the answer will likely be within the required tolerance. Assume L₁ = 3.2 m, L₂ = 5.3 m, M = 200 kN-m, and w =…