A glue-laminated timber beam is reinforced by carbon fiber reinforced plastic (CFRP) material bonded to its bottom surface. The cross section of the composite beam is shown in figure below. The elastic modulus of the wood is E= 12 GPa and the elastic modulus of the CFRP is 112 GPa. The simply supported beam spans L = 6 m and carries a concentrated load P=4.4 kN at midspan, see figure below. A If b₁ = 81 mm and b₂ = 35 mm determine: L/2 B L/2 CFRP b₁ y b₂ 250 mm 3 mm

A glue-laminated timber beam is reinforced by carbon fiber reinforced plastic (CFRP) material bonded to its bottom surface. The cross section of the composite beam is shown in figure below. The elastic modulus of the wood is E= 12 GPa and the elastic modulus of the CFRP is 112 GPa. The simply supported beam spans L = 6 m and carries a concentrated load P=4.4 kN at midspan, see figure below. A If b₁ = 81 mm and b₂ = 35 mm determine: L/2 B L/2 CFRP b₁ y b₂ 250 mm 3 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As shown in the figure, a rigid beam with negligible weight is pinned at one end and attached to two vertical rods. The beam was initially horizontal before the load W = 50 kips was applied. Find the vertical movement of W. OL8 0.1267 mm W O 0.1368 mm W O 0.1344 mm W ON.8 0.2154 mm W A = 2 in² E = 12 x 105 psi Steel A = 0.5 in2 Pino E = 29 x 10° psi H L = 3 ft L = 10 ft ←3 ft → 8 ft 4 ft W Spring Bronze VITTO
d) moment of inertia about the horizontal centroidal axis for transformed CFRP. Enter your answer in mm¹ to 2 decimal places.
The horizontal beam AB of 1.8-2 cross-sectional dimensions (b x h = 19 mm x 200 mm) is supported by the inclined support CD and is under the load of P = 12 kN at point B [see Fig. (a)]. The struts consisting of two rods, each 5b/8 in thickness, are connected to the beam by bolts penetrating the three rods at point C [see Fig. (b)]. (a) If the allowable shear stress of the bolt is 90 MPa, what is the minimum diameter dmin required for the bolt at point C? (b) If the allowable pressure stress of the bolt is 130 MPa, what is the minimum diameter dmin required for the bolt at point C?
Figure 1 ilustrates a cross-section af an aircraft fuselage. The floor beam of the aircraft is supported by the fuselage at its both ends. The floor beam has an I-shaped cross-section and is subjected to 1.2 kNim uniformly distributed load at ts center. It is assumed that the fuselage only exerts vertical reactions on the ends of the beam and El is constant 1.2 kNim -24 m Figure 1: Cross-section of an aircraft fuselage. (a) Construct a free body diagram (FBD) of the floor beam, with al necessary labes. (b) Determine the support reactions at A and D. (c) Construct shear force and bending moment diagrams for the floor beam. (d) Derive equation of beam defiection under the uniformly distributed load, in terms of E, 1, and distance x. (e) Determine the maximum deflection of the floor beam in terms of E and I. () if the floor beam is made of rolled-steel w250-58 with Young's modulus of 200 GPa, calculate the maximum deflection of the floor beam to the nearest mm.
In the figure, aluminum [E = 75 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a cross-sectional area of 330 mm² and link (2) has a cross-sectional area of 560 mm2. For an applied load of P = 37 kN, determine the rigid beam deflection vg at point B. Assume a = 1790 mm, b = 850 mm, L₁= 2420 mm, and L₂ = 4030 mm. L₁ (1) Answer: vg = i B b (2) mm. L2
A composite beam is made of two brass [E =101 GPa] plates bonded to an aluminum [E =64 GPa] bar, as shown in Figure below. The beam is subjected to a bending moment of 2030 N-m acting about the z axis. Assume b=53 mm, d1=52 mm, d2 =11 mm, Determine: (a)the maximum bending stresses in the brass plates and the aluminum bar. (b) the stress in the brass at the joints where the two materials are bonded together.
1. Horizontal beam ACB with cross section dimensions (width = b) (height = h) as shown in the figure below, on the inclined strut CD and joint B.be under load P The strut consists of two bars. The thickness of 5b / 8 is 3 bars meeting at joint C.The beam is connected by a passing bolt. a) Sketch the free body diagram of figure (a) and find the reaction in A and D.b) What is the minimum required diameter of the bolt at C if the allowable shear stress of the bolt is τa?c) What is the minimum required diameter of the bolt at C if the bearing stress allowed on the bolt is σb?
3. 4 For the beams shown in the figure below, L = 2m, P = 5000N, E = 70 GPa, I = 2x10-4 mª (a) Determine the deflection and rotation angle in the middle point. (b) Find reaction force and moment in B. A L 2 P 77 L 2 B
2kN/ m y = kx? vertex 3 m A 1 m 3 m 2kN/ m A cantilever beam (fixed at A) is acted upon by a cubic distributed load as shown in the figure. Calculate the support reactions at point A. FBD is mandatory.
The beam shown in the figure has a roller support at A, a fixed support at C and an internal hinge at B. The lengths of segments AB and BC are a and b respectively. A uniformly distributed load, q, is applied between points B and C, and a concentrated load P acts at a distance a/2 from the support A. EI is constant. a/2 P por quity A B Figure 2: Beam with internal hinge Determine the expression for the elastic curve (v(x)) for segment BC using the method of superposition. Use a = 2 m, b = 3 m, E = 70 GPa, I = 198 × 106 mm4, P = 10 kN and q = 2 kN/m.
2. In a laboratory test of a beam loaded by end couples, the fibers at layer AB in Figure below are found to increase 60 x 10-3 mm whereas those at CD decrease 100 x 103 mm in the 200-mm-gage length. Using E=70 GPa, determine the flexural stress in the top and bottom fibers. 200 mm 30 mm B 120 mm 30 mm Hello sir, please solve detailed details, boring, new article, I didn't understand anything, please sir, thank you sir. A how detailed solution
In the figure, aluminum [E = 75 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a cross-sectional area of 330 mm² and link (2) has a cross-sectional area of 560 mm2. For an applied load of P = 37 kN, determine the rigid beam deflection vg at point B. Assume a = 1790 mm, b = 850 mm, L₁= 2420 mm, and L₂ = 4030 mm. L₁ (1) Answer: vg = i B b (2) mm. L2