A wide-flange member (W 10 x 30) is compressed by axial loads that have a resultant P = 30 kips acting at the point shown in the figure. P = 30 kips W 10 x 30 The material is steel with modulus of elasticity E = 29,000 ksi. Assuming pinned-end conditions, determine the maximum permissible length Lmax (in ft) if the deflection is not to exceed of the length. 500 0.08 Your response differs significantly from the correct answer. Rework your solution from the beginning and check each step carefully. ft

A wide-flange member (W 10 x 30) is compressed by axial loads that have a resultant P = 30 kips acting at the point shown in the figure. P = 30 kips W 10 x 30 The material is steel with modulus of elasticity E = 29,000 ksi. Assuming pinned-end conditions, determine the maximum permissible length Lmax (in ft) if the deflection is not to exceed of the length. 500 0.08 Your response differs significantly from the correct answer. Rework your solution from the beginning and check each step carefully. ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simply supported wood beam of length L = 11 ft carries a concentrated load P at midspan, as shown. The cross-sectional dimensions of the beam are b = 7 in. and h = 13 in. If the allowable shear strength of the wood is 125 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. A Answer: P = 2 P B lb 12 L C X Z b h
A W18x71 A36 steel beam is loaded as shown on the figure. Neglect the weight of the beam. a. Determine the vertical shear stress of the beam.
Consider the uniformly loaded (w= 100 lbf/in) and simply supported steel beam with an overhang, as shown in the figure. Given L = 8 in and a = 6 in. The area moment of inertia of the beam /= 0.05 in 4. Use singularity functions to determine the deflection at the midway between the supports and at the end of the beam. L w The deflection at mid-span is The deflection at the end of the beam is in. B a in.
(B) // The straight beam with distribution load as shown in figure B is simply supported by a pin at A and a rod attached to point C. Determine the shear stress in (a) the pin at A and (b) the pin at C. Assume the pins have diameters of 0.6 in known the distribution load q = 1.4 kip/ft 2ft -3 ft 1.5 ft- TTTIT
As shown in the figure, a rigid beam with negligible weight is pinned at one end and attached to two vertical rods. The beam was initially horizontal before the load W = 50 kips was applied. Find the vertical movement of W. OL8 0.1267 mm W O 0.1368 mm W O 0.1344 mm W ON.8 0.2154 mm W A = 2 in² E = 12 x 105 psi Steel A = 0.5 in2 Pino E = 29 x 10° psi H L = 3 ft L = 10 ft ←3 ft → 8 ft 4 ft W Spring Bronze VITTO
A hollow, circular, steel column (E = 30,000 ksi) is subjected to a compressive load P. The column has length L = 8.0 ft and outside diameter d = 7.5 in. The load P = 85 k. If the allowable compressive stress is 7000 psi and the allowable shortening of the column is 0.02 in., what is the minimum required wall thickness t min?
Determine the vertical deflection at point A
A rectangular steel bar supports the two overhanging loads shown in the figure. Using superposition, find the deflection at the ends and at the center. 250 250 500 N | S00 N Dimensions in milimelers. Bar, b = 9, h = 35
The link CE (Diameter D=12mm) and DF (Diameter D=10 mm) are 300 mm 200 mm connected to rigid link ABCD as shown in the figure. The links CE and DF - 450 mm- are made of E=200 GPa steel. B A D Ca a. Find the force at each link (CE and DF) b. Find the deflection at point A. 32 kN 600 mm 750 mm E F
Question: A barrier gate was hit ba a car and deflected as shown in the figure. Treat the barrier boom as a cantilever made of aluminium with E=70 GPa. Determine the force P caused the deflection if : a. The boom's cross section is solid 60 mm 90mm №3 m b. The boom's cross section is hollow with wall thickness of 5mm. boom 0.3 m 0 60 mm 90 mm
100mm given with the load condition in the figure at point A where the shaft of diameter is Calculate the slope of the elastic curve. E=200 GPa as =1m and P=6 kN is given. elastic at point A What does the slope of the curve represent? Please explain.
HOMEWORK: Q1/ A beam carries the loads shown in figure, if the tensile stress must not exceed 20 MPa and the compression stress 70MPA. Find the maximum value of load P 50mm はomm W=2.5p Kw/m 300 Im tan 4m lom ww 150mm Q2/ A beam has a cross section as shown below with unknown dimensions of the flange (b,) and the web (b,) and is subject to a maximum positive moment at the center which causes a tensile stresses at points A and B of 900N/cm2 and 600 N/cm? respectively ba 10 J00KN 50 Cm sm 200cm