In the figure, rigid bar ABC is supported by axial member (1), which has a cross-sectional area of 400 mm², an elastic modulus of E= 70 GPa, and a coefficient of thermal expansion of a = 22.5 x 10-6 /°C. The temperature rises 48°C causing deformation at pt. B. Determine the deflection at pt. C?

Q: The cylindrical gasoline tank on a tractor is 11 inches in diameter and 36 inches long. How many…

A:

Q: 8. This sheet metal section has 5 sets of drilled holes: A, B, C, D, and E. The holes within a set…

A: Given: The set of holes are equally spaced in horizontal direction. The five sets of drill holes are…

Q: A 10 cm diameter solid aluminum post is subjected to a horizontal force of V= 7.1 kN and a…

A:

Q: The beam in the figure below is subjected to a load P= 3.9 kN at its end. Young's modulus is 210 GPa…

A:

Q: corresponding Circle the letter to the view on the right that shows the result of rotating the…

A: Find Rotate the object about the given axis.

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: A wind turbine has a power coefficient C, = 0.46 and is able to generate 1.6 MW. What was the amount…

A:

Q: Round off the numbers in the following problems to three significant figures. Find the percent…

A:

Q: Round off the numbers in the following problems to three significant figures. Find the percent…

A: Given Data: The given number is N = 826.48 The number should have three significant figures, hence…

Q: A wind turbine has a power coefficient C, = 0.25 and %3D is able to generate 1.3 MW. What was the…

A: Given    Wind power generated, P = 1.3 MW                 Power coefficient = 025

Q: Can I get a more detailled explenation on how to get the numbers in the numetor in each fraction…

A:

Q: a) Solve for ox'. Express your answer in kilopounds per square inch to three significant figures. b)…

A:

Q: A 3500-lb automobile travels down a 10° inclined road at a speed of 20 ft/s. If the driver jams on…

A:

Q: A midsized Dozer weighs 41,000 pounds and has 175 hp. If the machine is working at 80% efficiency…

A: Given Data The weight of the machine is: W=41000 lb The power is: P=175 hp The efficiency of the…

Q: The beam in the figure below is subjected to a load P= 3.9 kN at its end. Young's modulus is 210 GPa…

A:

Q: An 4 cylinder engine has a crankshaft sp of 3,500 rpm, a bore of 3.8 inches, a str of 3.8 inches,…

A: Givenk=4N=3500 rpmd=3.8in =3.8×0.0254=0.09652mL=3.8in=3.8×0.0254=0.09652mP=210…

Q: The beam in the figure below is subjected to a load P= 3.9 kN at its end. Young's modulus is 210 GPa…

A: P = 3.9 kNE = 210 GPa I = 5 * 106 mm4a = 1.5 mb= 1.3m

Q: Find the area of the figure shown. a=3 cm b= 6 cm Take pie3D3.14 Round answer to one decimal place.…

A: It is required to determine area of given section

Q: Round off the numbers in the following problems to three significant figures. Find the percent…

A: Original Number = 6748.3 After Round off up to three significant number = 6750

Q: An electric traction motor provides a torque of 400 N.m while rotating through 60 revolutions in 4…

A: The objective of the question is to calculate the electrical power input to an electric traction…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.