. A cantilever beam with square cross-section of 6 mm side is subjected to a load of 2 kN normal to the top surface as shown in the figure. The Young's modulus of elasticity or the material of the beam is 210 GPa fl magnitude of slope (in radian) at Q (20 mm from the fixed end) is 20 mm, 2 KN 100 mm

. A cantilever beam with square cross-section of 6 mm side is subjected to a load of 2 kN normal to the top surface as shown in the figure. The Young's modulus of elasticity or the material of the beam is 210 GPa fl magnitude of slope (in radian) at Q (20 mm from the fixed end) is 20 mm, 2 KN 100 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer quickly. Thanks!
Question 1) F=35 kN single load, M=45 kN.m moment and w=16 kN/m distributed load are acting on the beam whose loading condition is given in the figure. The length L is also given as L=4 m. The cross-sectional properties of the beam are; body height yg=225 mm, body thickness xg=14 mm, flange width xf=194 mm, flange height yf=11 mm. Point P on the section is located just above the flange-body junction. It is desired to determine the stress state at the P point in the section taken from the B line of the beam. According to this;Question1-A) Find the shear force (VB) at point B. (Write your result in kN.)Question1-B) Find the bending moment (MB) at point B. (Write your result in kN.m.)Question 1-C) Find the moment of inertia of the beam section. (Do your operations by converting the lengths to meters. Take at least 4 digits for the decimal part of your result and use the expression E for the decimal part. Write it as 5E-3 instead of 0.005.)
A wood beam with a rectangular cross section(see figure) is simply supported on a span oflength L. The longitudinal axis of the beam is horizontal,and the cross section is tilted at an angle α.The load on the beam is a vertical uniform load ofintensity q acting through the centroid C.Determine the orientation of the neutral axisand calculate the maximum tensile stress σmax ifb = 80 mm, h =140 mm, L =1.75 m, α = 22.58, andq = 7.5 kN/m.
A beam is loaded as shown in the figure. The length 1-20 in. and the load locations are a=10 in. and b= 15 in. The beam is steel with E = 30 Mpsi. The magnitude of the concentrated force is F= 500 lb and the distributed load is 50 lb/in. The dimensions of the beam cross-section are h = 5 and t = 2. You will be finding the deflection and slope at the end of the beam. a b 1 W F
A steel beam of I cross-section is simply supported on a span of 4m. Find the safe uniformly distributed load the beam can carry if the tensile stress is not to exceed 26 N/mm2. Also find the maximum compressive stress.
h F The beam of length 5.9 (m) and cross section base 0.10 (m) and height 0.16 (m) shown is made of plain steel with a modulus of elasticity of 200 (Gpa) and an ultimate strength of 400 (Mpa). The load is 250 (N) and the point q is 4.0 (m) from the wall in the x direction. What is the magnitude of vertical deflection of the beam at point q in units of meters?
The beam AB, shown in Figure 1a, with length L = 4.5 m is subjected to a uniform distributed load w = 13 kN/m and a concentrated moment M = 18 kN.m applied at point B. The beam has a rectangular cross-section with height h = 183 mm, width b = 98 mm, and constant thickness t = 12.5 mm as shown in Figure 1b. Take E = 200 GPa. 1 Determine the slope at point B 2 Determine the vertical displacement at point B [
Q2/ A beam with two overhang carries a uniform load of intensity w N/m, and support as shown in figure below. Determine the maximum permissible value of load w N/m. Given: the allowable tensile and compressive stress of 20Mpa. The beam has a rectangular cross section area with high-50mm and width=100mm 1m w N/m 2.5m 1-3 B 1m