It's a one question but it consists from multiple parts minimum number of crosspoints. Howmany crosspoints does the networkcontain?(b) If the occupancy of the trunks is 0.4 E andconnections are to be made to particularoutgoing trunks, estimate the grade ofservice. State any assumptions you make.(c) Redesign the above network to provide agrade of service better than 1 in 1000.How many crosspoints does this networkrequire?(d) Redesign the network to be strictlynonblocking. How many crosspoints doesthis network require? (a) Design a fully interconnectedthree-stage network with 200 incomingand 200 outgoing trunks with the

Answered: Image /qna-images/answer/8dc133a6-aed9-4aaf-bc57-1da7fad9e150.jpg

Answered: minimum number of crosspoints. How many…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter8: Symmetrical Components

Section: Chapter Questions

Problem 8.10P

See similar textbooks

Similar questions

What is a borrowing strategy in fixed channel assignments?a) Borrowing channels from neighbouring cellb) Borrowing channels from neighbouring clusterc) Borrowing channels from same celld) Borrowing channels from other base station in same cell
Solve it fast plz
30) In a lightly loaded long distance EHV lines, line loading is and has a power factor: (A) Capacitive, lagging. (B) Capacitive, leading (C) Inductive, lagging (D) Inductive, leading. please contact me in whatsapp +962782974574
The expression of Q factor for Schering bridge is given by
(b) Figure Q.4b shows an Adder/Subtractor circuit implemented using Adder Q. The delay for XOR = 2t, OR = AND=1t and cascadable full adder is used for ripple carry adder. Assume inputs X, Y and ADDSUB have arrived at Ot. Analyze the critical path delay for the circuit if:- X[7.4] YI7.4] 4. A[3.0] A[3.0] lo"cle C4 C8 C4 Adder Q co C4 Adder Q co ADDSUB Sum(3.0] Sum[3.0] Z17.4] Figure Q.4b i. Adder Q is a 4-bit Ripple-Carry Adder. Show your analysis in Table Q.4b.i. ii. Adder Q is a 4-bit Carry-Lookahead Adder. Show your analysis in Table Q.4b.ii. Table Q.4b.i Table Q.4b.ii To Node Delay To Node Delay Z3 Z3 С4 С4 Z7 Z7 C8 C8 Page 14 of 21
Q4) Two binary symmetric channel BSC are connected in cascade as shown below: Find i- The equivalent channel matrix, then plot the final model. ii- Determine overall Channel capacity, efficiency and redundancy. X1 0.75 yi 0.75 p(x1)=0.65 p(x2)= ? X2 0.82 y2 0.82 Z2
write aveport connectivity gateway on to LNOT using NOR
7. In the circuit below write the loop equations and set up (not solve) the matrix equation for the load current. Wiso 150 75 28 100
A digital communication link consists of nine regenerative repeaters along with a receiver. Signal from the transmitter is BPSK and regenerative repeaters have a bit-error probability of 5 times 10 -8 . (a) Calculate the overall probability of error. (b) Calculate the overall probability of error if regenerative repeaters are replaced by repeater amplifiers. Please solve as soon as possible..I`ll surely give a big like.
Q.6. ABC organization wants to manage its four offices A, B, C and D. This organization has network information (200.20.110.0-200 20.110.255). For each subnet find subnet mask, network ID, first assignable IP, last assignable IP, and broadcast addresses. (Show IP Addresses in decimal as well as in binary) Answer
I want a solution in less than 30 minutes Often, the network is referred as an infinite bus when a change in input mechanical power or in field excitation to the unit does not cause an appreciable change in a. system frequency or terminal voltage b. Total production cost c. system frequency and terminal voltage d. system frequency alone
Q4/ Why the performance of multimode graded index is better than multimode step index? Q5/ Design fiber optics communication system with analogue input and then measure the performance of the three types of fiber optics configurations. After that, answer the following questions: 1. Which configuration is the better? Comment! 2. Which parameters that improve the performance of multimode step index? Comment! 3. Which parameters that improve the performance of multimode graded index? Comment! 4. Which parameters that improve the performance of single mode step index? Comment! 5. If we need to increase the fiber length from 1 km to 15 km. which configuration is used? Comment!

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning