A dc voltage of unknown value Vand internal resistance Reis connected through a switchto a lossless transmission line of Zo = 1000. If the first 5 μS of the voltages at z = 0 and z =L are observed to be as shown below, calculate Vo, RG, the load resistanceR,, and thetransit time T.100+ [V]:-0. V90[V]:-V10075I, Տ1,μs2460246

Answered: Image /qna-images/answer/b58b701a-648c-4a86-b8c6-70b68fe756d5.jpg

Answered: A dc voltage of unknown value Vand…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter13: Transmission Lines: Transient Operation

Section: Chapter Questions

Problem 13.17P

See similar textbooks

Similar questions

Name t=0 502 8012 502 COAXIAL CABLE 5000 m A swikh closing at t=0 sends a voltage daun a s000m transmission line with a velocity facter of .8 Calculate : a) The magnitue of the incident voltage traveling to Hhe load. 6) The rellecion coeficient c) The magnikle of the refleckd voltage d) The voltage on the line after all reflections have ceased. e) The time for all reflectias to cease
Please help with the solution.
Transmission Lines: There is an electrically short lossless 50 ohm coax cable connected to a load impedance of 60 kilo ohm. The frequency is 10 kHz and e_r = 2.05. Consider a length of l = 3 m. What is the input impedance of this line?
1. a. A purely reactive load impedance Z₁ =jX terminates a transmission line. Prove that the reflection coefficient magnitude |K| is always unity, assuming the characteristic impedance Zo is real. What is the VSWR of the line in this case? b. Consider the transmission line in the figure. i. Determine the SWR on transmission line ii. The input impedance If=102, find I, in the figure. WC 100/0*V] 20 922 Air, lossless Z-50 £2 2.72 40 2 ele 3002
Q5: A 50-W lossless line terminated in a purely resistive load has a voltage standing wave ratio of 3. Find all possible values of ZL. Ans: T = 0.5, Z, = 150N & 152
RL=30
A 50 transmission line is to be connected to a 72 load through a 1/4 quarter wave matching transformer. (a) What must be the characteristic impedance of the transmission line that is used to form the quarter wave transformer? (b) If the frequency of operation is 7 MHz and the phase velocity through the quarter wave section is 2c/3, what is the length of the quarter wave section? You may assume the transmission line forming the quarter wave section is lossless.
A quarter-wave transmission line is used to match a 25 $2 load to a 75 $2 generator, i.e. the input impedance seen from the generator needs to be 75 $2. The A/4 transformer is lossless with E, 2.25 and the generator operates at 2 GHz. a. Calculate the physical length of the A/4 transformer (in meters) b. What should the characteristic impedance of the A/4 transformer be? c. Find out and compare the time-average power delivered to the load with and without the X/4 transformer if the generator voltage amplitude is 10 V. d. Calculate the voltage standing wave ratio on the X/4 transformer.
Q5. Find the differential equations describing the below line model, in that the resistors of the line model are removed. So, you can follow the way we found the differential equations for lines in class, but remove the resistors (both series and parallel, this model is a simplified model and called lossless line model). U(x,t) U(x+Ax,t) C'
i need clear ans by hand and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛ | I need a detailed explanation of the steps
30) In a lightly loaded long distance EHV lines, line loading is and has a power factor: (A) Capacitive, lagging. (B) Capacitive, leading (C) Inductive, lagging (D) Inductive, leading. please contact me in whatsapp +962782974574
The length of a transmission line is (1000/3) kilometers. For this transmission line r=0.15 ohm/km x=0.8 Ohm/km y=5 * 10^-6 S/km given in the form. At the end of the line (36) MW is drawn and the end-of-line voltage is (220) kV. power factor: 0.95 (back) a. Assuming the line as a short line, calculate the VS and IS values with their angles. b. A, B, C, D by accepting the line as a mid-length line and using the "T" model approach. Calculate the parameters (Vs Is calculation is not needed) C. Calculate only parameter A, assuming the line as a long line.

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning