=A generator with VG 300V and R = 50 is connected to a load R = 750 through a 50 losslesstransmission line of length L = 0.15 m. (a) Compute Zin, the input impedance of the line at thegenerator end. (b) Compute and V. (c) Compute the time-average power Pin delivered to the line.(d) Compute VL, IL, and the time-average power delivered to the load, PL (e) How does Pin compareto PL? Explain.

Answered: = A generator with VG 300V and R = 50…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.15MCQ

See similar textbooks

Similar questions

A three-phase, 60-Hz, untransposed transmission line runs in parallel with a telephone line for 20 km. The power line carries a balanced three-phase rms current of Ia = 3202 – 240°A. The line configuration is as shown in figure. Assume zero current flows in the ungrounded telephone wires. Find the magnitude of the voltage induced in the telephone line. = 32020°A, Ī, = 3204–120°A, and a 4 m 4 m 5 m d G2 mO
1/ Power loss due to corona is: a. Inversely proportional to frequency. b. Proportional to frequency. c. Frequency does not effect. d. All these answers are wrong. 2/ We prefer High voltage DC (HVDC) transmission system than High Voltage AC transmission system according to the cost, when: a. The distance of the line is more than B00 km. b. The distance of the line is less than 300 km. c. The distance of the line is equal to 300 km. d. All the above answers are wrong. 3/ HVDC Transmission has lower corona losses than HVAC Transmission because: a. HVDC Transmission tower is less height than HVAC Transmission tower. b. HVDC Transmission system work with zero frequency than HVAC Transmission system of 50 Hz. c. HVDC Transmission currents is uniform distributed in the all cross section of the system conductors than HVAC Transmission due to skin effect. d. All of the above answers are wright.
The impedance of the 500 km long transmission line is Z = 0.1 + j * 0.4 ohm / km. At the end of the line, 988.1 A current is drawn under 400 kV interphase voltage. The angle of the current is -68. It is 6 degrees. With the short transmission line equations, the amplitude value of the phase neutral value of the busbar voltage to which the generator at the beginning of the line is connected is given correctly. A) 231.34 B) 52.35 C) 400 D) 380.28 E) 388.57
A DC generator of voltage Vg and internal resistance Rg is connected to a lossy transmission line characterised by a resistance per unit length R and a conductance per unit length G. a.)Write the governing voltage and current transmission line eequations. b.)Find the general solutions for v(z) and I(z). c.)Specialise the solutions in part(b) to those for an infinte line. d.)Specialize the solutions in part(b) to those for a finite line of length l that is terminated in a load resistance Rl.
Q4(b) The equivalent circuit of a single phase short transmission line is shown in Figure Q4(b). Here, the total line resistance and inductance are shown as lumped instead of being distributed. i) Sketch the phasor diagram and assess with by labeling the details for the A.C. series circuit shown in Figure Q4(b) for the lagging power factor at load point (Vn). ii) Summarize, what if the load change from low value to high value shown in Figure Q4(b). R XL el Vs Vn Figure Q4(b) Load
Develop a small-scale equivalent transmission line pi model (per phase) of the transmission lines with the specification given in table 1. The conductors are placed with a flat horizontal spacing of 7.25 meters. Consider that the load connected against the line 125MW at 0.85 lagging power factor. You are required to develop an equivalent model for a maximum 220V (RMS) sending and receiving end voltage and a maximum of 5A load current. Sr. NTDC Transmission Line Length Conductor No. Туре 220 kV DG Khan-Loralai Transmission Line (227 km) 227km Pheasant TABLE AJ Electrical characteristics of bare aluminum conductors steel-relnforced (ACSR)+ Reniertance Reactance per conductor 1-ft apacing. 60 Ha Ae, 60 Ha Capaitive Aluminum ares, emil Layers of Outaide aluminum diameter, in a/1,000 ft soC, D/ml GMR Induetive Stranding AL/8t De, 20°C. 20C, a/mi Code word D. t Ma-mi Waswing Partridge Ostrieh Merlin Linnet Oriole Chickndee Ibin Pelienn Flicker Hawk 266,800 206,800 300,000 336, 400 336.400…
Transmission line conductance is usually neglected in power system studies. True False
4. A 4160V, three phase source, 4-wire supplying an unbalanced three phase load. The unbalanced connected load are: Zan = 150/53.13° ; Zbn = 150-53.13° ; Zen = 1500° Assuming positive sequence and the reference is the line voltage "a", determine: a. the line current "a" b. the line current “b” c. the line current "c". d. the total real power e. the total reactive power f. the total apparent power g. the overall power factor. h. the neutral current.
The figure shows a 500-kV (line-to-line voltage) transmission line linking two systems. The theoretical maximum power that can be transferred from System A to System B is 5,000 MW, which occurs when the power angle 8 = 90°. The line current is then proportional to (VA - VB) The reactive power losses (Mvar) in the transmission line during this transfer would be most nearly: Wond O A. 1,667 O B.. 3,333 O C. 5,000 O D. 10,000 Know EQUIVALENT SYSTEM A VA= 500 28 KV m XL = 50 Ω EQUIVALENT SYSTEM B VB = 500 40⁰ kV O
1) A 60-Hz, ...-km, three-phase overhead transmission line has a series impedance z = 0.8431L79.04 ohm/km and a shunt admittance y = 5.105 × 106 L90 S/km. The load at the receiving end is 125 MW at unity power factor and at 215 KVLL. Determine the voltage, current, real and reactive power at the sending end and the percent voltage regulation of the line for nominal pi network. (Please determine the length of the transmission line within the specified limits: 150-220 km. By considering the length value you determined yourself, solve the question.)
Consider the 500 kV, three phase bundled conductor line as shown in the figure below. Find the line to neutral capacitance. 0.5 m 30 mm (0) (O to Ine 15 m 15 m
6.8. A three phase, 50 Hz, 100 km transmission line has resistance 0.1 ohms/km, inductance 111.7 mH/km and capacitance 0.9954 x 10- uF/ph per km. The line is delivering 20 MW at a 0.8 power factor lagging and 66 kV to a balanced load. Determine the efficiency and regulation. Use nominal it method. Ans. n= 93.5%, VR = 17.47%

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning