A circular shaft has a diameter D = 40 mm and a length L = 1.5 m and is made of structural steel with elastic perfectly plastic behavior (G= 95.98 GPa and Ty = 180 MPa). The shaft fixed at one end and subjected to a torque T at the other end. The angle of twist is measured between the ends as op = 0.2 rad. a) Calculate the yield shear strain yy. b) Calculate the maximum shear strain ymax. c) Determine the radius py to the elastic- plastic boundary. d) Determine the torque T. If the member has yielded and then unloaded. e) Determine the residual shear stress at p=5 mm. 0.001667 rad 0.0016774 rad 0.002 rad 0.0015 rad 0.00225 rad 0.002667 rad 0.001333 rad 0.004 rad 0.002 rad 0.002667 rad 12.5026 mm 12.5806 mm 12.5026 mm 8.3351 mm 16.6701 mm 15 mm 11.25 mm 16.875 mm 2.5171 kN.m 2.0426 kN.m 0.17138 kN.m 2.6323 KN.m 2.2927 kN.m 2.3981 KN.m 1.9212 kN.m 2.563 KN.m 106.6667 MPa 86.6667 MPa 53.33 MPa 80 MPa 120 MPa ㅈ

A circular shaft has a diameter D = 40 mm and a length L = 1.5 m and is made of structural steel with elastic perfectly plastic behavior (G= 95.98 GPa and Ty = 180 MPa). The shaft fixed at one end and subjected to a torque T at the other end. The angle of twist is measured between the ends as op = 0.2 rad. a) Calculate the yield shear strain yy. b) Calculate the maximum shear strain ymax. c) Determine the radius py to the elastic- plastic boundary. d) Determine the torque T. If the member has yielded and then unloaded. e) Determine the residual shear stress at p=5 mm. 0.001667 rad 0.0016774 rad 0.002 rad 0.0015 rad 0.00225 rad 0.002667 rad 0.001333 rad 0.004 rad 0.002 rad 0.002667 rad 12.5026 mm 12.5806 mm 12.5026 mm 8.3351 mm 16.6701 mm 15 mm 11.25 mm 16.875 mm 2.5171 kN.m 2.0426 kN.m 0.17138 kN.m 2.6323 KN.m 2.2927 kN.m 2.3981 KN.m 1.9212 kN.m 2.563 KN.m 106.6667 MPa 86.6667 MPa 53.33 MPa 80 MPa 120 MPa ㅈ

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.2.4P: A circular steel tube of length L = 1.0 m is loaded in torsion by torques T (see figure). (a) If the...

See similar textbooks

Similar questions

Solve the preceding problem if the length L = 56 in., the inner radius r1— 1.25 in., the angle of twist is 0.5°, and the allowable shear strain is 0.0004 rad.
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A tubular bar with outside diameterd2= 4.0 in, is twisted by torques T = 70,0 kip-in. (see figure). Under the action of these torques, the maximum tensile stress in the bar is found to be 6400 psi. Determine the inside diameter rtf of the bar. If the bar has length L = 48.0 in. and is made of aluminum with shear modulus G = 4,0 × 106 psi, what is the angle of twist d (in degrees) between the ends of the bar? (c) Determine the maximum shear strain y (in radians)?
A solid copper bar of circular cross section has length L = 1.25 m and shear modulus of elasticity G = 45 GPa. The bar is designed to carry a 250 N · m torque acting at the ends. If the allowable shear stress is 30 M Pa and the allowable angle of twist between the ends is 2.5°, what is the minimum required diameter?
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A solid circular bar of diameter d = 50 mm (see figure) is twisted in a testing maching until the applied torque reaches the value T = 500 N ·. At this value of torque, a strain gage oriented at 45º to the axis of the bar gives a reading e = 339 × 10-6. What is the shear modulus G of the material?