A circular aluminum tube subjected to pure torsion by torques T (see figure 2) has an outer radius 2 equal to 1.5 times the inner radius n. (a) If the maximum shear strain in the tube is measured as 400x10 rad, what is the shear strain y: at the inner surface? (b) If the maximum allowable rate of twist is 0.125 degrees per meter and the maximum shear strain is to be kept at 400x10° rad by adjusting the torque T, what is the minimum required outer radius (12) min? Figure 2: cylindrical shaft

A circular aluminum tube subjected to pure torsion by torques T (see figure 2) has an outer radius 2 equal to 1.5 times the inner radius n. (a) If the maximum shear strain in the tube is measured as 400x10 rad, what is the shear strain y: at the inner surface? (b) If the maximum allowable rate of twist is 0.125 degrees per meter and the maximum shear strain is to be kept at 400x10° rad by adjusting the torque T, what is the minimum required outer radius (12) min? Figure 2: cylindrical shaft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the resulting strains in a unidirectional lamina subjected to normal tensile stresses of 20MPa in the longitudinal direction, compressive stress of 5MPA in the transverse direction, and a negative shear stress of 1.0MPa. The lamina properties are: EL =20 GPa, ET = 2 GPa, GLT = 0.7 GPa, and vLT = 0.35.
Mechanics of deformable bodies
A circular tube is subjected to torsion by torques T applied at the ends. The bar is 0.75 m long and the inside and outside diameter are 35 mm and 46 mm respectively. It is determined by measurement that the angle of twist is 3.20 degrees when the torque is 600 N-m. (a) Calculate the maximum shear stress in the tube. (b) Calculate the shear modulus of elasticity. (c) Calculate the maximum shear strain in radians.
Here is a past question I'd like help with
The bar shown in the figure is made of cold-drawn steel, having an yield strength of 280 MPa. Loads applied are F = 1 kN, P = 5 kN, and torque T = 20 kN. For each element shown in the figure (element A and element B, separately, • Determine the principal stresses at A and B (eigenvalues) • Using DET, determine whether the bar will yield. What is the factor of safety for the loading situation shown, based on DET? 15-mm D. -100 mm
40 mm 10 mm 40 mm An aluminum tube with the cross section shown has a constant wall thickness 2 mm. A torque T= 400 N-m is applied to the tube. Use G= 28 GPa * What is the area of the tube? What is the total length of the median line? What will be the result shear flow of the object' The shearing stress value will be The angle of twist result is 20 mm
Figure Q4 (a) shows an L-bracket ABC with diameter d which lies in the horizontal plane. It is made from a material with elastic and shear moduli E and G, respectively. If a vertical load P is applied at end C, determine the total strain energy that is stored in the whole structure. Express your answer in terms of P, E, G, d and L. Neglect the strain energy due to shear force.
Two hard rubber blocks with Modulus of Rigidity equal to 350 kPa are used in an anti-vibration mount to support a small machine as shown below. Let a = 20 mm, b = 50 mm and c = 80 mm. Deterrmine: (a) the shearing strain in the rubber blocks when a downward deflection of 6.50 mm occurs due to P. (b) the magnitude of P. Include the figure showing the shearng strain and the FBD to support your force equation, (if there is any). Show the step by step solution.
An open-coiled helical spring consists of 12 coils, each of mean diameter 60 mm, wire diameter 6 mm and helix angle 25°. An axial load of 120 N is applied to the spring. Calculate (a) axial de- flection, (b) bending and shearing stresses, and (c) axial torque which shall produce a bending stress of 50 MPa in the coils. Take E = 200 MPa, and G = 84 GPa.
Consider a two-component rod fixed at the left end. The first component (on the left, positioned from z=0 to z=L/2) is a solid rod with a shear modulus of G and radius c1. The second component (on the right, positioned from z=L/2 to z=L) is a hollow pipe fixed to component 1 at z=L/2 with the same shear modulus and outer radius c1, but with an inner radius of c2. A torque of 6To is applied at z=L/2, and a torque of -2To is applied at z=L. What value of c2 is required to make the maximum shear stress equivalent in each component? What is the angle of twist at the free end at z=L?
A circular tube of aluminum is subjected to torsion by torques T applied at the ends (see figure). The bar is10 in. long, and the inside and outside diameters are 1.2 in. and 1.6 in., respectively. It is determined by measurement that the angle of twist is 3.037° when the torque is 52,681 lb-in. Calculate the shear modulus of elasticity G in psi.
Consider the loaded shaft illustrated in Figure Q4 (i). The shaft is simply supported at A and D. The shoulder fillet radius is 0.3 cm at B and C. If the shaft is subjected to a force of F-800 N, determine the following: (a) The reaction forces at the two ends of the shaft A and D. (b) The bending moments at shoulder fillets B andC. (c) The nominal stresses at shoulder fillets B and C. (d) The stress concentration factor at shoulder fillet B. (e) The maximum stress in the shaft taking into account stress concentrations. 800 N T-0.3 can A d, - 3 cm d, = 5 cm d, - 3 cm 5 cm 8 cm 8 cm 12 cm Figure Q4 (i) The reference parameters are shown in Figure Q4 (ii) in the page that follows. For 0.002 srlds 0.3 and 1.01 s Dlds 6.0, the stress concentration factor for bar bending is given as: kn -4.4 = 0.632 + 0.377 -0.14 – 0.363(P/a)" + 0.503(P/a) 1- 2.39(P/a) + 3.368(2la)* -0.5 The nominal stress is: 32M %3D nd3