A circular steel tube of length L = 1.1 m is loaded in torsion by torques T (see figure).TTr2(a) If the inner radius of the tube is r,= 51 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y, (in radians) at the inner surface? (Enter the magnitude.)rad(b) If the maximum allowable shear strain is 0.00043 rad and the angle of twist is to be kept at 0.45° by adjusting the torque T, what is the maximum permissible outer radius (r,)may (in mm)?mm

a) The given values are - L=1.1 m=1100 mm, r1 =51mm, θ=0.5°=0.5×π180radThe shear strain is given by…

Answered: A circular steel tube of length L = 1.1…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bar shown in the figure is made of cold-drawn steel, having an yield strength of 280 MPa. Loads applied are F = 1 kN, P = 5 kN, and torque T = 20 kN. For each element shown in the figure (element A and element B, separately, • Determine the principal stresses at A and B (eigenvalues) • Using DET, determine whether the bar will yield. What is the factor of safety for the loading situation shown, based on DET? 15-mm D. -100 mm
A 3 m long steel angle shown in the figure has a section thickness of 12.7 mm and a cross sectional area of 4350 mm². Since tem = 50 MPa and G = 77.2 GPa, find the maximum applicable torque T.
Two hard rubber blocks with Modulus of Rigidity equal to 350 kPa are used in an anti-vibration mount to support a small machine as shown below. Let a = 20 mm, b = 50 mm and c = 80 mm. Deterrmine: (a) the shearing strain in the rubber blocks when a downward deflection of 6.50 mm occurs due to P. (b) the magnitude of P. Include the figure showing the shearng strain and the FBD to support your force equation, (if there is any). Show the step by step solution.
A round steel rod is subjected to axial tensile stress of 50 MPa with superimposed torsional shear stress of 100 MPa (see the figure). If the material has tensile yield strength Syp of 500 MPa, determine the factor of safety by applying 1. Maximum shear stress theory, and 2. Maximum distortion energy theory.. S 500 MPa = 100 MFa 0,50 MPa
T.L Tr4 %3D J = " (r* – rf) (Tubular shaft) Tr (Solid shaft) G.J 3. The shaft in the figure below consists of 75 mm diameter bronze segment that is rigidly joint to 50 diameter steel segment. The ends of the shaft are attached to rigid supports (fixed supports). Calculate the absolute maximum shear stress developed in each segment when the torque T= 5.1 kN-m is applied (a = 2 m and b = 1.5 m). Use G = 35 GPa for bronze, and G = 75 GPa for steel. (21 pts) 75 mm 50 mm Bronze Steel
A thin tube of uniform thickness 5 mm and square cross section, shown below, is subject to a torque of 1500 N·m. The shear modulus of the material is 80 GPa. What will be the angle of twist per length (in unit: rad/m)? 50 mm 50 mm
A shaft ABCD is supported by a clamp at point A and is subjected to point torques at B, C and D, as shown in the figure. The shaft has variable cross-section and is solid in segments AB and CD and hollow in segment BC. The lengths and diameters of each segment are shown in the figure. Assume that the deformation is linear elastic and take the shear modulus of elasticity G = 12.1 × 10° psi. a) Using method of sections, plot the torsion moment diagram. b) Find the angle of twist for the free end (point D) with respect to the fixed support at A, QAD and the angle of twist for point C with respect to the fixed support at A, QCA. Find both angles in degrees. d₁ = 4 in d20 3.5 in, d2=2.5 in d3 = 3.0 in 25 kip-in 20 kip-in 10 kip-in A 20 in B с D ++ 25 in 30 in
A circular hollow shaft is subjected to a torsional moment T = 30 kNm and a compressiveload P = 80 kN, as shown. The shaft has an outer diameter D = 120 mmand inner diameter d = 100 mm. Points A and B are on the surface of the shaft. (a)Calculate the direct and shear stress at point A. (b)Calculate the maximum,minimum and oriention of the max and min principal stresses at point A. (c)Calculate the maximum in-plane shear stress at point A and the orientation.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS