A tubular aluminum bar (G = 28 GPa) of squarecross section in Figure with outside dimensions50 mm x50 mm must resist a torque T = 340N m. Calculate the minimum required wall50 mmthickness t if the allowable shear stress is 31MPa and the allowable angle of twist Ø perunit length is 0.033 rad/m.50 mm

Answered: Image /qna-images/answer/28387052-3702-499a-a9ed-860f01ddc764.jpg

A tubular aluminum bar (G = 28 GPa) of sque cross section in Figure with outside dimension 50 mm x50 mm must resist a torque T = 340 N m. Calculate the minimum required wall thickness t if the allowable shear stress is 3 MPa and the allowable angle of twist Ø per unit length is 0.033 rad/m.

A tubular aluminum bar (G = 28 GPa) of sque cross section in Figure with outside dimension 50 mm x50 mm must resist a torque T = 340 N m. Calculate the minimum required wall thickness t if the allowable shear stress is 3 MPa and the allowable angle of twist Ø per unit length is 0.033 rad/m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Gkuestrons T ØD VP The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load: bending and torsion. The column contains an hemispherical groove of radius r, located at a distance L from the point of application of the loads. You are given the column diameter D = 68 mm, the groove radius r = 6 mm, the distance L= 200 mm, the bending load P=5 kN, and the torque T = 600 N.m. The material data are Young's modulus E = 122 GPa Shear Modulus G = 55 GPa Poisson's ratio v= 0.1 and Yield strength oy = 380 MPa. a) Write a numbered list of the calculation steps required to obtain the factor of safety in yielding based on the maximum distortion energy (Von Mises) criterion.
The circular cross-section, L=0.5m long console BC shaft in the figure is forced to twist with P1=2 kN, P2=8 kN due to the forces on the belts connected to the pulley C. The radius of the pulley is R=0.4m and its weight is W=3 kN. Calculate shaft diameter D based on the assumption of maximum shear stress (TRESCA). Yield strength of the shaft = 240MPa and safety factor is S=2 1 kasnak D 2R P2 |B kayış y
I need the answer as soon as possible
I need the answer as soon as possible
For the frame shown in the figure, Find the normal and shear stresses based on the following information: Diameter of pin A is 10mm- Double shear Diameter of pin C is 15mm-Single ahear. 20 m 600 mm 25 60 (26x50) mm A B00 mm 30 k
In the figure, there is a steel shaft where moment is applied from the C point. The modulus of elasticity of this shaft is 210 GPa and its shear modulus is 80 GPa. The material of the shaft is Ç1010 and the yield stress is 240 MPa.Find the shaft diameters Dab, Dbc, Dcd, Dde and the torsion angle between A and E according to the Vonmises hypothesis by taking the safety coefficient as 2
The shaft in Figure below consists of a 3-in. -diameter aluminum segment that is rigidly joined to a 2-in. -diameter steel segment. The ends of the shaft are attached to rigid supports, Calculate the maximum shear stress developed in each segment when the torque T= 10 kip.in is applied. Use G = 4×106 psi for aluminum and G = 12×106 psi for steel. Aluminum 3-in. diameter 6 ft T Steel 2-in. diameter 3 ft
A circular steel tube of length L = 1.1 m is loaded in torsion by torques T (see figure). T T r2 (a) If the inner radius of the tube is r, = 51 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y, (in radians) at the inner surface? (Enter the magnitude.) rad (b) If the maximum allowable shear strain is 0.00043 rad and the angle of twist is to be kept at 0.45° by adjusting the torque T, what is the maximum permissible outer radius (r,)may (in mm)? mm
A circular hollow shaft is subjected to a torsional moment T = 30 kNm and a compressiveload P = 80 kN, as shown. The shaft has an outer diameter D = 120 mmand inner diameter d = 100 mm. Points A and B are on the surface of the shaft. (a)Calculate the direct and shear stress at point A. (b)Calculate the maximum,minimum and oriention of the max and min principal stresses at point A. (c)Calculate the maximum in-plane shear stress at point A and the orientation.
A torque of Tx=200Nm and a torque of Mz=260Nm are applied to the stepped shaft in the figure. Calculate the maximum stresses that will occur in the bar section, taking into account the stress concentration.
A hellcal spring Ils made by wrapplng steel wire 20 mm diameter around a forming cyllnder 160 mm in diameter. Calculate the elongatilon of the spring wlthout exceeding a shearing stress of 150 MPa If It ls composed of 20 turns. Let G=80,000 MPa. (Ans. 127.4 mm)
The hollow cylinder shaft shown in the figure has an inside diameter of 15mm and the gears are subjected to the indicated load. The bearings at points A and B only exert forces on the shaft in the y and z directions. If the allowable shear stress is known to be operm = 70 MPa. Use the maximum shear stress theory of failure and proceed to:a) Draw the bending moment diagrams My and Mz and torque T, determine the magnitude and location of the absolute Maximum Moment.b) Determine the outer diameter of the shaft to within 1 mm.