A central mix plant is producing concrete at a rate of 110 cubic yards per hour (cy/hr), with plant efficiency already taken into account.A slipform paver is being used to pave a 10-foot wide, 12 inch thick concrete pavement.Assuming paver efficiency is 75%, what average paver speed in feet per minute will match the plant production? Group of answer choices 3.71 4.95 6.60 1.22

A central mix plant is producing concrete at a rate of 110 cubic yards per hour (cy/hr), with plant efficiency already taken into account.A slipform paver is being used to pave a 10-foot wide, 12 inch thick concrete pavement.Assuming paver efficiency is 75%, what average paver speed in feet per minute will match the plant production? Group of answer choices 3.71 4.95 6.60 1.22

Fundamentals Of Construction Estimating

4th Edition

ISBN:9781337399395

Author:Pratt, David J.

Publisher:Pratt, David J.

Chapter11: Pricing Concrete Work

Section: Chapter Questions

Problem 4RQ

See similar textbooks

Similar questions

Given the specifications for an asphaltic concrete mixture and the results of a sieve analysis, determine the proportion of different aggregates to obtain the required gradation. Coarse aggregates: 60% Fine aggregates: 35% Filler: 5%
Two materials, A and B, are to be separated using two unit operations, 1 and 2. The feed has 10 tons/h A and 4 tons/h B. The split (fraction of material rejected by each operation) is given in Table P5-14. a. Which sequence of operations, (l?2) or (2?1), will yield the greatest recovery of material A? b. What will be the purity of material A using that sequence? c. What will be the efficiency of separation for the entire process train with regard to material A using the Worrell-Stesed equation?
In concrete work, Fuller and Thompson (1907) suggested that a dense packing of grains can be achieved if the percent finer (p) and grain size (D) are related by the following equation, where n is a constant varying in the range of 0.3-0.6. Dmax is the size of the largest grain within the soil. p=(DDmax)n100 This equation is sometimes used in roadwork for selecting the aggregates. a. For n = 0.5, show that the soil is well graded. b. If n = 0.5 and Dmax = 19.0 mm, find the percentages of gravel, sand, and fines within the soil. Use the Unified Soil Classification System.
According to Figure 5-20, is ii possible to completely separate one of the four materials from the other three? Explain your answer.
Portland cement concrete consists of what four primary elements?
Three groups of students from the Geotechnical Engineering class collected soil-aggregate samples for laboratory testing from a recycled aggregate processing plant in Palm Beach County, Florida. Three samples, denoted by Soil A, Soil B, and Soil C, were collected from three locations of the aggregate stockpile, and sieve analyses were conducted (see Figure 2.35). (a) (b) Figure 2.35 (a) Soil-aggregate stockpile; (b) sieve analysis (Courtesy of Khaled Sobhan, Florida Atlantic University, Boca Raton, Florida) a. Determine the coefficient of uniformity and the coefficient of gradation for Soils A, B, and C. b. Which one is coarser: Soil A or Soil C? Justify your answer. c. Although the soils are obtained from the same stockpile, why are the curves so different? (Hint: Comment on particle segregation and representative field sampling.) d. Determine the percentages of gravel, sand and fines according to Unified Soil Classification System.
An existing rural 4-lane highway is to be replaced by a 6-lane divided expressway (3 lanes in each direction). Traffic volume data on the highway indicate that the AADT (both directions) during the first year of operation is 24,000 with the following vehicle mix and axle loads. Passengercars=50percent 2-axle single-unit trucks (12,000lb/axle)=40percent 3-axle single-unit trucks (16,000lb/axle)=10percent The vehicle mix is expected to remain the same throughout the design life of 20 years, although traffic is expected to grow at a rate of 3.5 percent annually. Using the AASHTO design procedure, determine the minimum depth of concrete pavement required for the design period of 20 years. Pi=4.5J=3.2Pt=2.5Cd=1.0Sc=650lb/in.2So=0.3Ec=5106lb/in.2R=95k=130lb/in.3