A block of uniform material and length L = 1000 mm, width b = 375 %3D %3D mm, and depth d = 65 mm, is floating in a liquid. It assumes the position shown in the figure below when a uniform vertical load of 20 N/m is applied at P. Find the weight of the block. If the load is suddenly removed, what is the righting moment before the block starts to move? * P W Fg

A block of uniform material and length L = 1000 mm, width b = 375 %3D %3D mm, and depth d = 65 mm, is floating in a liquid. It assumes the position shown in the figure below when a uniform vertical load of 20 N/m is applied at P. Find the weight of the block. If the load is suddenly removed, what is the righting moment before the block starts to move? * P W Fg

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Wire BC has a diameter of 0.10 in. And its material has the stress-strain characteristics shown in the figure. Determine the vertical displacement of the handle D if the pull on the handle is slowly increased and reaches the magnitude of P = 655 lb. o (ksi) 40 pulg 80 70 B 50 pulg - 30 pulg € (pulg/pulg) 0.007 0.12
H.W A rigid slab weighing 600 ku is Placed uron two bronze vads and one Steel Vocd Cnch of bo00 mm? area at a temfevature of 15 Ĉ as shown, find the temperature at which the stress in steel Vad willbe zero? take: Cuefficlent of exransion for Steel = 12 Mm/m. Coefficient of exPansion for bronze = 18Mm/m.c %3D Joung's modulus for Steel = 2e0Gla Young's modulus for bronze = 80 Gra %3D 600W bronze Steel
1. A solid shaft ABCD of diameter d is fixed at A and subjected to torques applied at equally spaced points B and C as indicated in the figure. [total length L, torsional rigidity Glp.]. a. Determine the reacting torques at A and D. b. Draw a diagram showing the variation of the torque in the different segments. c. What is the minimum required diameter if the material has an allowable stress tallow? d. Find the twist of the points B and C relative to A. 3т. 5T
Note: Give me right solution according to the question. If any data missing assume that. A wheel applies 40 kN load on a semi-infinite elastic space as shown in Figure. The modulus of elasticity of the material is 150 MPa and the Poisson’s ratio is 0.38. Assume the load is applied on the surface as a concentrated force. The vertical deformation at a depth of 500 mm at the centerline of the wheel is most nearly: 0.64 mm 0.07 mm 0.41 mm 0.26 mm
A 20 mm x 120 mm beam is subjected to a load of 50 kN acting at the centroid of the cross section as shown in the figure. Point B is 20 mm below the centerline of the beam. A. Find the shearing stress at point B. B. Find the minimum principal stress component on the 30 degrees plane at point B. Please give me the solutions of this with these answers: Answers: A. Ans: -16.67 MPa B. Ans: 2.98 MPa
Find the bulk modulus of elasticity of a liquid of pressure 150 psi applied to 10 ft^3 of the liquid causes a volume reduction of 0.02 ft^3. (Choices: a) 75000 psi b) 108000 psi c) 750 psi d)7500 psi)
The stresses shown in the figure act at a point on the free surface of a machine component. If 0 = 31 MPa in the direction shown, determine the normal stress Oy at the point. Txy O 42.4 MPa O 30.8 MPa O 24.9 MPa O 22.6 MPa O 32.3 MPa Ox 30° 27 MPa 50 MPa
Given an element with stresses as indicated in fig. 1; find: a) The principal stresses b) The normal and shear stresses on a plane inclined at 25% from the horizontal. c) The maximum shear stress. d) Draw the Mohr's circle. sono stare boods Sheet Mus 100 kPa 20 35 20 kPa Horizontal led to builty in 35 kPath bullta Madre Hip y 100 kPait bun
1500 KN 800 mm 70 mm 100 mm 1500 KN A bar has a length of 800 mm, width 100 mm, and thickness 70 mm, and is being subjected to 1500 KN of tension as shown. As a result, the length of the bar as increased to 802.5 mm and its width has decreased to 99.906 mm. Assume elastic behavior. a) Determine the Young's modulus (E) of the material b) Determine the Poisson's ratio (v) of the material c) Determine the Shear modulus (G) of the material d) Determine the new thickness of the bar in mm e) Determine the percentage change in the total volume of the bar
Review The beam is made from a plate that has a constant thickness b. (Figure 1) Part A If it is simply supported and carries the distributed loading shown, determine the variation of its depth as a function of z, 0 Submit Request Answer wo Provide Feedback Next > ho |B
A rigid slab weighing 600 ku is placed upon two ·bronze rods and one steel rod each of 6000 mm² area at a temperature of 15¢ as shown, find the temperature at which the stress in steel rod will be Zero? take: Coefficient of expansion for steel = 12 um/m. c coefficient of expansion for bronze = 18 um/m. c Young's modulus for steel = 200 G Va Young's modulus for bronze = 80 GPa 600 IN 250mm 300mm -bronze -Steel
500 MPa b 0.006 120 KN 100 mm b) Determine the rod's new length under this load c) Determine the rod's new diameter under this load 20 mm 120 kN A rod 100 mm long with a diameter of 20 mm is subject to 120 kN of tension as shown, alongside with the stress-strain curve of its material. Assume a Poisson's ratio of 0.35. a) For the given load condition, is the rod behaving elastically or plastically? Explain your reasoning The tensile load is now removed, and the ends are now subject to a shear force of 10 KN in the same plane as the cross-section (i.e., the force is acting "horizontally"). Assume elastic behavior. d) Determine the shear strain resulting from this shear force (ignoring any bending effects) e) What is the horizontal displacement of one end of the rod relative to the other end under this shear force?