From the given figure, determine the value of the horizontal force P if the coefficient of static friction in all contact surfaces is 0.40....200kgP12 wedgeA) 2586 NB2391 Nc) 2685 ND2865 NE) 3224 NF) 3422 N1932 N1392 N

Answered: Image /qna-images/answer/985c92d5-e6e6-424f-b4c2-95f8b819a219.jpg

Answered: From the given figure, determine the…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 10-lb force is pushing the 40-lb block as shown. The incline angle of the plane is α=40º . The coefficient of static friction between the block and the incline is μs = 0.75 and the coefficient of kinetic friction is μk = 0.65. Will the block slide on the plane? If it does, will it slide up or down the plane? What is the friction force between the block and the plane?
The inverted T-beam supports the concentrated loads shown in Figure. Determine the following: What is the location of the neutral axis relative to the bottom of the beam? What is the moment of inertia of the beam section with respect to the NA? What is the maximum positive moment in the beam (in terms of P)? What is the maximum negative moment in the beam (in terms of P)? What is the maximum allowable value of P in order not to exceed a flexural stress of 4ksi in compression? What is the maximum allowable value of P in order not to exceed a flexural stress of 10ksi in tension? What is the maximum allowable value of P for this beam such that it will not fail by bending?
A brass disk of radius 0.7 ftft and weight 459 lblb sits in a right-angle groove made of granite. The disk makes contact with the groove at AA and BB and the coefficient of static friction at both points are μS=μS= 0.39 A couple moment of MM is applied to the disk as shown.
The wheel weighs 20 lb and rests on a surface for which μB = 0.2. A cord wrapped around it is attached to the top of the 30-lb homogeneous block. If the coefficient of static friction at D is μD = 0.3, determine the smallestvertical force that can be applied tangentially to the wheel which will cause motion to impend.
A block with mass (m = 19.5 kg) is pulled with a force (F = 280 N) 0 = 25°. a) Draw a free-body diagram. b) Find the normal force. c) If coefficient of friction between the crate and the surface is uz=0.12, what is the value of the frictional force, fr. d) Find the acceleration. e) What minimum horizontal force is needed to move the block with a constant speed (while keeping the F = 280 N)? F m
Question 2) Find the shear center of the section below and calculate the maximum shear stress that occurs in the section as a result of the loading shown in the figure. The section thickness is uniform everywhere and is 10 mm. Note: G.M is the geometry center of the section, the shear force of 40 kN acts from the geometry center of the section. You can look at your lecture notes for the coefficients you will need. 160 mm V-40 kN t LG.M 100 mm
For the beam shown in the figure below, determine the reaction at point C using the singularity functions. Also, determine the most economical W-shape for the beam if the maximum allowable deflection at B is 6 mm (refer to the properties of the rolled-steel - W shape provided). The beam's modulus of elasticity is 200 GPa. The distance 'a' is 3 metre, distance 'b' is 2.5 metre, and the distance 'c' is 3.5 metre. The distributed load, w, is 30 N/m. The load, P is 200 N. P W H A C B W-shape cross-section a b
The cross section of a bearing block is shown in the figure by the shaded area. Calculate the moment of inertia of the section about its base a-a. Assume b= 11 in, h = 3 in., r = 2 in, R = 3 in. Answer:lo-s=1 b R in.4 h
Determine the velocity in ft/s of the 8-lb block when t = 5 s if the block has a speed of 10 ft/s when the force of F = (10.9t2) Ib is applied. The coefficient of kinetic friction at the surface is µk = 0.17. F
The 113-lb force P is applied to the 230-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume μs = P Answer: F = 0.48, Mk = 0.38. i Mk lb
An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The minimum force P required to prevent rotation of the flywheel is applied. a.) Which Tension is larger, TA Oor TB? Explain b.) What is the angle of contact in radians? c.) What is the value of the ratio TA/TB? 800 N.m 60 60° A B
1. A typical cross-section of a roinforced concrete T-beam is shown in the figure below. The beam is reinforced with eight 25 mm diameter bars in tension zone. For the purpose of analysis, use the effoctive depth of 575 mm. Use f. = 25 MPa and f, = 420 MPa. Determine øM, 1000 mm T100 mm 8-D25 300 mm 575 mm ww G29

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

From the given figure, determine the value of the horizontal force P if the coefficient of static friction in all contact surfaces is 0.40. ... 200kg P 12 wedge