In the figure below, the block weight is 200 N, upslope force A = 50 N, and downslope force B = 20 N. If the slope angle is 30 degrees, will the block remain in static equilibrium? A Slope angle = 0 Hs = 0.5 W O block will remain in static equilibirum O block will accelerate upslope O block will accelerate downslope

In the figure below, the block weight is 200 N, upslope force A = 50 N, and downslope force B = 20 N. If the slope angle is 30 degrees, will the block remain in static equilibrium? A Slope angle = 0 Hs = 0.5 W O block will remain in static equilibirum O block will accelerate upslope O block will accelerate downslope

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A vertical tapered rod of length L has its diameter varying linearly from 'd' at lower end to D at the upper end which has fixed support. Young's modulus of the material is E. Show that the elongation 4FL of the rod at its lower end when subjected to a longitudinal force Fis given by 8 TdDE
Q4 Determine the vertical displacement at joint A, if members AB and BC experience a temperature increase of AT = 200°F. Use the following data: E = 29 (10) ksi A= 2 in? a = 6.60 (10)" /°F AB = BC = CD = 8 ft - %3D E B A 500 lb 1000 Ib Figure 4
1
A beam has a cross-section as shown in Figure Q5. The beam is subjected to a vertical shearing force of 100KN through the shear centre. For the system: a) determine the second moment of area about the x - x plane and b) determine the shear stress distribution along the y – y plane, c) plot the shear stress distribution on a suitable graph, labelling the principal values. y! Centre of Gravity. y' 30 тm 60 тm шш 09 120 тт
For the figure shown, if the tensile force in member AB is 38 kN and the allowable stress is 120 MPa, then the ....... area of member BC is AV 256.7 mm^2 O 457.1 mm^2 O 316.66 mm^2 O 304.7 mm^2 419.5 mm^2 O W
A newtonian fluid flows down an infinitely long cyalindrical tube (as shown in the figure below). There is NO applied pressure gradient, and fluid flows down the pipe due to gravity alone.i) Derive the velocity profile (?(?) =?). ii)Find???? ,???iii) Draw the velocity and shear stress profiles, showing the points where ? or ? is equal to zero or at their maximum value.
Using the Clayperon Method, Determine: 1. Support Reaction 2. Internal forces (Shear Force, Normal Force and Bending Moment) 3. Draw the Internal force diagrams P1= 3.246 kN P2- 4.846 kN q- 1.846 kN/n s2 1,946 3,246 3,946 3,946 3,946 3,94268 L
A simply supported beam of length 7 m has a concentrated couple M of 10 kN-m applied at the right end. Determine the location of the maximum deflection from the applied load. O 2.75 m O 2.96 m O 2.50 m O 2.252 m Calculate the value of the maximum deflection. Use E = 200, 000 N/mm^2 and I = 60x10^6 mm^4. O2.62 mm O 131 mm 10.52 mm 5.26 mm
Limiting states 1. The MC describes the state of stress of our point in the field. That is, the MC shows us the values of the two principal stresses and the value of the maximum shear stress that the point is sustaining in the field. Consider a point in a geostatic soil mass. For our point, o'vo = 100 kPa and o'ho = 40 kPa. Take a sheet of paper and draw the Mohr Circle for this point carefully. 2. Now, we know that o'ho is a principal stress because t = 0 on the vertical plane (in the field). Similarly, o'vo is a principal stress because t = 0 on the horizontal plane (in the field). What is the value of t on the plane inclined 45 degrees clockwise from the horizontal? Go ahead and use your drawn MC to find this value. The value should be t = 30 kPa. 3. Note that the value found (t = 30 kPa) is the maximum shear stress that the point is supporting in the field, as it is under o'v = 100 kPa and o'h = 40 kPa. Consider now a situation in which o'h remains at 40 kPa, but o'y grows to 120…
Determine the Magnitude and direction of Resultant of the forces as shown in Figure P-001 F2 = 50 kN F1 58 kN 30 F = 40 kN F = 45 kN Figure P-001