A batch reactor is to be used to treat raw water to achieve 95% pollutant removal. The pollutant has a second-order reaction rate constant of 0.35 L/(mg.day), what is the required residence time of water in the batch reactor, in days? For the same water in ab

Q: What is the hydraulic retention time?  b. What would be concentration decay model along the relative…

A: a) Hydraulic detention timeThe hydraulic detention time (th) is given by th =VQ=3000 m3600m3day=5…

Q: The raw water supply for a community contains 160 mg/L total particulate matter. It is to be…

A:

Q: 5. A disinfection process destroys E.coli in water. The influent c coliforms/mL. If the reactor…

A:

Q: It is found in a water sample that it has insufficient alkalinity and therefore soda ash (Na2CO3) is…

A:

Q: A wastewater contains 0.2 M pyruvate. Estimate the volume of methane in liters (STP) that would be…

A: Given, 0.2M pyruvate t = 15 days

Q: A flue gas contains mainly 15 micron sized particles (density 2000 kg/m3) to be removed by a cyclone…

A: INTRODUCTION- Flue gas also known as exhaust gas or stack gas is a gas emitted by combustion plants…

Q: Calculate the theoretical oxygen demand of the ASP reactor with a reactor inflow rate of 23000…

A: Give Data :- So = 165 mg/l S = 26 mg/l Q = 23000 m^3/day Total Yield Y = 0.48 SRT = 7 days Decay…

Q: Consider an ideal refrigeration cycle that has a condenser pressure 1000 KPa and an evaporator…

A: Pressure is acting on the inclined wall while the load is generating in the area of the element. The…

Q: 4. What does the analytical scale read? (Ans: 1.550 g) 5. What is the concentration of the Total…

A: Given, Flow rate (Q) =  20 mgd  Volume (V) = 90 ml or 0.09 L

Q: Example :- Calculate the power in W/m required for mixing an oil of relative density 0.93 and…

A: The given data is as follows: Relative density of oil=0.93Viscosity of oil=18 N.s/m2Diameter of…

Q: Look at the following information for a completely mixed biological reactor: tank volume = 200 m³;…

A: Given- Tank volume V=200 m3 Flow rate=50 m3/day Substrate concentration=95 mg BOD5/L Ks=60 mg BOD5/L…

Q: The figure below shows a completely mixed reactor receiving two inflows. Assuming steady state for…

A: Given, Cin, 1 = 25 mg/L Cin, 2 = 10 mg/L Q1 = 10 L/min Q2 = 5 L/min

Q: 1. Consider a reactor operating at 50% power with Tave = 572°F. Assume the following: 1. A fuel…

A:

Q: An industry is planning to use a 250 m3 bioreactor to treat 400 m3/day of wastewater containing 80…

A: As per honor code only three sub-parts are answered at a time so please upload separately for…

Q: Develop a mathematical expression of three phase fluidized bed reactor for first order catalytic…

A: Fluidized Bed Reactor : The fluidized bead reactor has the ability of processing the large volumes…

Q: thermal oxidizer incinerator operates as a plug flow reactor at a temperature of 250 deg C. The…

A:

Q: Calculate the gas molecular weight.

A: Given:- T=25oC1 atmV=80m3/minN2=75%O2=5%H2O=8%CO2=12%To find:-molecular weight

Q: An activated sludge tank, 30 ×30 ×150 ft, is designed as a plug-flow reactor, with an influent BOD…

A:

Q: Sea water can be desalinated by using reverse osmosis. A plant treats 4,000 m3 /day of feed water…

A:

Q: A medium containing 50 g/L of S (substrate) is continuously fed into a completely mixed reaction…

A: The Monad equation is a mathematical equation used in environmental engineering to predict…

Q: Consider the following data from a test on : Pelton wheel: Head at the base of the nozzle = 32 m…

A: Pelton wheel having head H = 32 mDischarge Q = 0.18 m3/secarea of jet = 7500 mm2 = 7500 X 106 m2To…

Q: 250 lbs. of contaminated soil containing 0.500 g of a pollutant per kilogram of soil will be treated…

A: Given, Mass of contaminated soil = 250 lb or 113.4 kg  Concentration of pollutant, Co = 0.5 gm/kg…

Q: An electrostatic precipitator (ESP) with 5600 m² of collector plate area is 96 percent efficient in…

A: Given data- Area A1=5600 m2efficiency n1=96%efficiency n2=99%To Find-ESP collector area A2

Q: n use sludge recycle.

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: A plug-flow reactor (PFR) has an influent flow with a concentration of 100 mg/L of A and a flowrate…

A: Reference : Water Resources, Hydrology. Given : Concentration and flow rate. Rate constant for first…

Q: 2. Domestic "tap" water generally has a conductivity in the range 0.5 - 1.0 ms/cm. Based on your…

A: The total amount of dissoloved salt in water can be easily estimated by measuring the specific…

Q: An ASP operating at equilibrium has an organic loading rate of 2 kg/m³/d and has MLSS of 3000 ratio…

A:

Q: The disinfection of water is carried out in a stirred tank. The treatment process has water as the…

A: Given: The input rate is 48000 L/h. The volume of tank is 3500 L. The  rate of disinfectant is…

Q: You are studying a reactor that receives a particular reactive contaminant which follows a zero…

A: Given: Reaction rate, k=0.5 mg/L min [A]0=10 mg/L [A]t=1 mg/L Average velocity=10 cm/sec

Q: The removal of phenol in an industrial waste stream by microorganisms can be characterized as a…

A: Step 1: To determine the most efficient reactor configuration for the removal of phenol in the…

Q: 3. A solution is known to contain 42 mg/L of C6H₁2O6. Determine the theoretical oxygen demand.

A:

Q: A reactor that behaves as an ideal PFR is to be used to carry out a BOD removal reaction. The…

A:

Q: Help me solve both for my homework. Thank you!

A:

Q: Environmental Engineering: Water Treatment Please consider each of the following points: a.…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: stack with an inside radius of 1 m.  The plant emits 300 g/s of SO2 from the stack with an exit…

A:

Q: The reaction rate coefficient is 0.06 day. Determine the reaction rate model that uses this…

A:

Reactions with Materials

Limestone