(5) [Text - problem 4.32] Solve for 50 and 95% efficiency Compare the reactor volume required to achieve 95% efficiency for a CMFR and a PFR for the following conditions: steady-state, first-order reaction, flow rate = 14 m³ day, and reaction rate coefficient 0.05 day-¹.

(5) [Text - problem 4.32] Solve for 50 and 95% efficiency Compare the reactor volume required to achieve 95% efficiency for a CMFR and a PFR for the following conditions: steady-state, first-order reaction, flow rate = 14 m³ day, and reaction rate coefficient 0.05 day-¹.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: What is the hydraulic retention time? b. What would be concentration decay model along the relative…

A: a) Hydraulic detention timeThe hydraulic detention time (th) is given by th =VQ=3000 m3600m3day=5…

Q: An electrostatic precipitator (ESP) with 5600 m? of collector plate area is 96 percent efficient in…

Q: Determine the ultimate 1st stage BOD. Calculate the 1-day BOD. What would be the 5 day B0 if the…

A: 5 day BOD5 at 20°C = 150 mg/lk=0.20day-1Let BOD ultimate = L0 thenBOD5=L0(1-e-kt)

Q: A Carnot engine uses hydrogen as its medium. The volumes at the beginning and end of the reversible…

Q: A flue gas contains mainly 15 micron sized particles (density 2000 kg/m3) to be removed by a cyclone…

A: INTRODUCTION- Flue gas also known as exhaust gas or stack gas is a gas emitted by combustion plants…

Q: Calculate the theoretical oxygen demand of the ASP reactor with a reactor inflow rate of 23000…

A: Give Data :- So = 165 mg/l S = 26 mg/l Q = 23000 m^3/day Total Yield Y = 0.48 SRT = 7 days Decay…

Q: Lubricating oil at 20°C with a density of 871 kg/m³ and a kinematic viscosity of 1.5 x 105 m²/s…

A: Density of the oil = 871 kg/m3 Kinematic velocity (ν) = 1.5×10-5 Inner radius (Ri) = 0.04 m Outer…

Q: The figure below shows a completely mixed reactor receiving two inflows. Assuming steady state for…

A: Given, Cin, 1 = 25 mg/L Cin, 2 = 10 mg/L Q1 = 10 L/min Q2 = 5 L/min

Q: 1. Consider a reactor operating at 50% power with Tave = 572°F. Assume the following: 1. A fuel…

Q: Develop a mathematical expression of three phase fluidized bed reactor for first order catalytic…

A: Fluidized Bed Reactor : The fluidized bead reactor has the ability of processing the large volumes…

Q: For an SBR process, the sludge takes 45 minutes to settle and the depth of liquid in the reactor is…

A: Given data- SBR process Sludge takes 45 minutes to settle. The depth of liquid in the reactor is 40%…

Q: The change in head across a small turbine is 10 m, the flow rate of water is 1 m³/s and the…

A: Given data: Head length, h = 10 m. Flow rate, Q = 1 m3/s Efficiency, η=0.8 Density of water, ρ=1000…

Q: a pollution-free stream at a flow rate known flow rate and concentration. Tl sume the nollutant can…

Q: Prob-3 A cyclic machine, shown in Fig. below receives 300 kJ from a 1000 K energy reservoir. It…

A: The high temperature of the energy reservoir TH=1000 KThe low temperature reservoir, TL=400 KEnergy…

Q: Problem 3. A news broadcaster report that the barometric pressure is 30.40 in of mercury. Calculate…

Q: 6.10. A reactor that behaves as an ideal PFR is to be used to carry out a BOD removal reaction. The…

A: Given BOD removal reactor with removal rate formula. Influent BODu = 150 g/m3 Effluent BODu= 20 g/m3…

Q: A desalination plant produces fresh water from seawater at 10°C with a salinity of 3.2 percent on…

Q: An activated sludge tank, 30 ×30 ×150 ft, is designed as a plug-flow reactor, with an influent BOD…

Q: A CFSTR receives a flow rate of 100 m³/sec. There is one influent stream coming into the reactor and…

A: Given data: Flow rate received by the CFSTR: Q=100 m3/s The concentration of the chemical in…

Q: A medium containing 50 g/L of S (substrate) is continuously fed into a completely mixed reaction…

A: The Monad equation is a mathematical equation used in environmental engineering to predict…

Q: (a) Prove that for a first order decay reaction (k1= 2 days-1) taking place in reactors of identical…

A: k = 2 days-1 (first order rate constant)V=Reactor volume= 15 LCin=Inlet contaminant concentration =…

Q: An electrostatic precipitator (ESP) with 5600 m² of collector plate area is 96 percent efficient in…

A: Given data- Area A1=5600 m2efficiency n1=96%efficiency n2=99%To Find-ESP collector area A2

Q: hat reactor volume is required for a CMFR to achieve 95% efficiency assuming a flow rate of 14m ^ 3…

A: According to given data CMFR to achieve 95% efficiency assuming a flow rate of 14m ^ 3 / d anda…

Q: A batch reactor is to be used to treat raw water to achieve 95% pollutant removal. The pollutant has…

A: According to given data A batch reactor is to be used to treat raw water to achieve 95% pollutant…

Q: Power can be generated in principle by utilizing the naturally occurring decrease with depth of the…

Q: n use sludge recycle.

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: A plug-flow reactor (PFR) has an influent flow with a concentration of 100 mg/L of A and a flowrate…

A: Reference : Water Resources, Hydrology. Given : Concentration and flow rate. Rate constant for first…

Q: 2. Domestic "tap" water generally has a conductivity in the range 0.5 - 1.0 ms/cm. Based on your…

A: The total amount of dissoloved salt in water can be easily estimated by measuring the specific…

Q: A heat engine with 0.305 mol of a monatomic gas undergoes the cyclic procedure shown in the pV…

A: Using the given data, we can calculate the temperature at stage 1 (T1) and stage 3 (T3), and then…

Q: Q1) At a particular time, the storage in a river reach is 60 x 103 m 3 . At that time, the inflow…

Q: 1. Oil that has a density of 880 kg/m flows under a head of 30 m. The pipe that the oil flows…

A: We have to determine the flow in dm3/sec as per the given data in the question and we have to also…

Q: Steam enters a turbine at 15bar and 600°C with a rate of 0.371 kg/s. The steam expands to 0.08 bar…

Q: A pump delivers 0.05 m³/s of water with a head of 55 m and runs at a speed of 1470 rpm for 8 hours…

A: The shaft power (in watts) can be calculated using the formula:Where,Ps = Shaft power (in watts)Q =…

Q: For an SBR process, the sludge takes 45 minutes to settle and the depth of liquid in the reactor is…

A: total time allowed for one operation in SBR processT=45+20+10+60=135 minFlow rate Q=55000…

Q: You are studying a reactor that receives a particular reactive contaminant which follows a zero…

A: Given: Reaction rate, k=0.5 mg/L min [A]0=10 mg/L [A]t=1 mg/L Average velocity=10 cm/sec

Q: The removal of phenol in an industrial waste stream by microorganisms can be characterized as a…

A: Step 1: To determine the most efficient reactor configuration for the removal of phenol in the…

Q: A reactor that behaves as an ideal PFR is to be used to carry out a BOD removal reaction. The…

Q: Find in cubic meters the volume of this horizontal oil furnace.

A: Given:- A horizontal oil furnace is given The length of the furnace is 1.5 m The width of the…

Q: spillway, hence, the percentage of energy dissipated

Q: Environmental Engineering: Water Treatment Please consider each of the following points: a.…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Question

(5) [Text - problem 4.32] Solve for 50 and 95% efficiency
Compare the reactor volume required to achieve 95% efficiency for a CMFR and a PFR for the following
conditions: steady-state, first-order reaction, flow rate = 14 m³ day, and reaction rate coefficient =
0.05 day-¹.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Taking given data.

VIEW

Step 2: Finding final and initial concentration of reactants ratio

VIEW

Step 3: Deriving volume of completely mixed flow reactor (CMFR)

VIEW

Step 4: Finding Volume of CMFR for both 95% and 50% efficiencies

VIEW

Step 5: Deriving volume of PFR

VIEW

Step 6: Finding Volume of PFR for both 95% and 50% efficiencies

VIEW

Solution

VIEW

Step by step

Solved in 7 steps with 33 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A power plant in rough terrain has a 100-m stack with an inside radius of 1 m. The plant emits 300 g/s of SO2 from the stack with an exit velocity of 10 m/s at a temperature of 120oC. Ambient temperature is 6oC and the temperature increases at a rate of 2 K/km. At 10 m above ground, surface windspeed is 1.5 m/s on a mostly cloudy night. Find the concentration (mg/m3) of SO2: Directly downwind at a distance of 2 km. At a point located 2 km downwind and 0.1 km off the downwind axis. At the point downwind where it is a maximum. Approximately how far from the stack does this occur?
I need hand written solution only otherwise I will down vote
In DGD 3, question 1, an algebraic equation for four CSTR in series was derived. Acontinuation of the same question. Determine -a) The total mean residence time and total volume for the four reactors. Express thevolume in m3.b) The mean residence time and volume for a single CSTR having the same conversion of‘X’.c) The mean residence time and volume for a single PFR having the same conversion of ‘X’.Express volume as gallons and m3.d) As the number of CSTR’s in series increases, the system approaches a___________?
Q20. Calculate the first-order reaction rate constant in days for the given data. The number of CFSTRS in series are 5. The influent BODS is 160 g/m and final effluent BOD5 is 10 g/m. The hydraulic residence time of each reactor is 1 h. Determine the detention time of a PFR that will produce same effluent quality as that from the series of reactors.
What type of reactor meets with the following conditions? 1) complete mixing; 2) continuous flow
Derive E(t), F(t), tm, and σ2 for a turbulent flow reactor with 1/7 the power law, i.e.,
At critical depth O The discharge is maximum for a given specific energy. O The specific energy is maximum for a maximum discharge. O The specific energy is minimum for a maximum discharge. O The discharge is minimum for a given specific energy.
1. Draw control volume diagram of reactors for each of the following conditions and write down the mass balance equations using different notations shown in figure: C, Qout Cin Qin V, C Reaction rate constant =k Figure: Sample CMFR/CFSTR showing influent and effluent flows, volume, reaction rate components. a) Steady state CMFR/CFSTR with conservative pollutant b) Steady state CMFR/CFSTR with non-conservative pollutant having first order growth rate c) Non-steady state CMFR/CFSTR with non-conservative pollutants having second order decay rate
Determine the pollutant removal efficiency (%) in an ideal plug flow reactor having hydraulic detention time τ=5hr for a hazardous chemical having a first-order decay rate constant of k=0.40hr−1. Hydraulic detention time = 5 hours.
Compare the size of a CMER and a PFR to achieve 50 percent removal of a contaminant, given a flow rate of 1000O m3/d and a first-order rate constant of -0.4/h. Repeat for 99 percent removal. Comment on the relative efficiency of each type of reactor and the situations where each type of reactor may be useful.
3. A first order decay reaction is occurring in a single CFSTR. Dividing the reactor into two smaller CFSTRs that are operated in series (effluent from one serving as the influent to the other) reduces the overall mixing and therefore makes the flow more PFR-like. Because reaction efficiency is greater in a PFR than a CFSTR, we might expect that dividing the reactor would improve the efficiency. To test that hypothesis, consider a system receiving an influent with C = 100 mg/L of a reactant that undergoes a first order decay reaction with a rate constant of 0.1 min ¹. Assume that the system has a total hydraulic detention time of 1 hour, but that it can be operated in three different ways: as a PFR, a CFSTR, or as two CFSTRs in series with the detention time split equally between the two. Find the effluent concentrations for the three possible operating modes
A 15 m wide rectangular channel carries a discharge of 30 m³/sec under critical conditions. If the width of the channel is increased to 20 m, then the ratio of specific energy at critical depth for 15 m width to 20 m width will be m. (up to two decimal places)