(a) A storage tank is connected to a piping system as illustrated in Figure P1. Water at temperature of 20°C in the storage tank flows through a piping system with the pipe's diameter of 5 cm and discharges from a nozzle to the atmospheric at velocity of 3.5 m/s. The diameter of the nozzle is 3cm. Galvanized pipe is used and installed in this piping system. All the fitting components installed in this system such as regular 90° and tees are flanged type. The Water at 20°C 21 m D= 5 cm d = 3 cm

Q: The sketch for the warm water heating system of a studio apartment is shown in the figure. The…

A: Given : The volumetric flow rate through the piping system = 0.000162 m3/s The different losses are…

Q: Compute the Cross sectional area of Pipe Discahrge=0.8 m3/s Velocity=2 m/s

A:

Q: The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter…

A: As per Bartleby Policy, in case of multiple subparts, only the first three subparts can be solved,…

Q: 1. Are pipe systems common in engineering applications?

A: (1)   The pipe systems are most commonly used in the engineering applications in mechanical as well…

Q: Select duct sizes for the rectangular duct system shown in the Figure, using the equal friction…

A: Given DataL=6mTotal pressure of the Duct=30PaPressure of Each Diffuser=5Pa Given System

Q: Determine the friction factor “f “for a 30 mm ID commercial steel pipe handling 300 L/min of water…

A:

Q: Determine the smallest metric hydraulic copper tube size that will carry 4L/min of the following…

A: Solution to part (d) as mentioned by the student:

Q: e below.. that 1.013*10° Pa ulate the absolute press sity: = = 1000 kg/m %3D

A: given:

Q: Find the pressure drop(kPa) in a 29m length of pipe with a triangular cross section. Q = 22m3/min f…

A:

Q: Determine the Darcy friction factor f in a fully developed flow in a pipe (diameter = 0.5 ft) made…

A:

Q: In Figure 7, oil with a specific gravity (s.g.) of 0.852 is to be forced from Tank A to Reservoir B…

A: Given: The specific gravity of oil, SG1 = 0.852 The total length of pipe, L = 38 m The diameter of…

Q: A duct of rectangular cross-section 600mm X 400mm carries 90 m3/min of air having a density of 1.2…

A: Given data  Rectangular Cross-section of duct = 600 mm * 400 mm discharge = 90 m3/min density = 1.2…

Q: Two tanks connected by three pipes in series are shown in Figure 2. The lengths of these pipes are…

A:

Q: Convert 104KPa to meters of H2O @ d= 15mm = 225psi to inches Hg in a pipe of circumference =…

A: INTRODUCTION: Unit conversion is the use of particular terminology to express values. The defined…

Q: Design the duct system shown below using Equal friction method, and determine the fan power when the…

A:

Q: The head loss of a 174 m length of tube having a diameter of 65 mm is 41 m. Oil flows through the…

A: The friction factor. Given: The length of the pipe is L=174 m. The diameter of the tube is D=65…

Q: Q.2) Air flows through a circular duct (D=0.4 m) at a velocity of 4 m/s, determine the pressure drop…

A:

Q: Determine the smallest metric hydraulic copper tube size that will carry 4L/min of the following…

A:

Q: l Resolving of Example (1-3) Two reservoirs with a difference in elevation of 15 m are connected by…

A:

Q: FOR THE PIPE NETWORKS SHOWN, THE FLOW OF WATER FROM A TO THE FIRST JUNCTION IS 2 CUBIC FEET PER…

A: given that , Q1=2 Av1=2 3.14✕0.335✕0.335✕v1=2 v1=2/0.35    =5.71ft/s Head loss is express by Darcy…

Q: Two tanks connected by three pipes in series are shown in Figure 2. The lengths of these pipes are…

A: (a) The diagram of the system is given as, The difference in water level in tanks is given as,

Q: hown in the figure below is a pipe system (commecial steel pipes) having a given centerline geometry…

A:

Q: A home hot water heater contains 40 gal of water. Because of a failure of the heat control, heat is…

A: The volume of water initially present=40gallon Pressure at which the tank rutures=250psig To…

Q: Three pipes of diameters 300 mm, 200 mm and 300 mm and lengths 450 m, 255 m and 315 m respectively…

A:

Q: Determine the velocity of the flow of water @45C is flowing through a 3-in ID smooth pipe. The…

A: given; diameter (d)=3 in                      =0.0762mdischarge through pipe(Q)=2.4lb/s…

Q: above the lower water surface. If the ency, what horsepower must be supp

A: Length of Pipe BC, LBC = 18 ftLength of pipe DE, LDE = 187 ftFriction factor, f = 0.035Kent = 0.8…

Q: A pipe has a diameter D and a friction factor f. Assume that f is constant due to a very large…

A:

Q: There is a PVC pipe, with an internal diameter of 28 mm. The Reynolds number for this system is…

A: here  D= 28 mm Re=1500  ε=0.0015 swami jain method ... f=0.25[log(ε/D3.7+5.74Re0.9)]2

Q: The diameter of the smooth pipes used in the pumping system in the lower figure is 150 mm and its…

A: Given: The diameter of pipe, d = 150 mm = 0.15 m The efficiency of pump = 0.84 The change in height…

Q: The loss coefficients for the pipe shown is: up to A it is 0.8, from A to B it is 1.2, from B to C…

A: Given Data: KA=0.8KA-B=1.2KB-C=0.8KC-D=2.2   To Find:

Q: 2. Prove that the frictional factor 'f' for laminar flow under pressure in a circular pipe is given…

A: Consider below sign convention followed for this question. Vavg = Average velocityμ = Dynamic…

Q: Oil flows in the circular pipe at 40 oC. If the Reynolds number is calculated as 1700, what is the…

A: Given data Oil flows in the circular pipe. T=40 oC Re = 1700

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.