A pump delivers 1000 gpm of water through a 200-mm diameter suction pipe and 150- mm discharge pipe. The suction and discharge pipes are 4 m and 20 m long, respectively. The water is delivered to reservoir 15 m above the intake water level (water source tank). The pump centerline is located 2 m above the intake water level Fittings and valves installed in the suction line are 1 standard elbow and 1 gate valve and in the discharge line are 3 standard elbows, 1 check valve and 1 gate valve. The pipe material used is cast Iron. Neglect friction losses. Determine: • Total Dynamic Head • Pressure head at the pump suction • Pressure head at the pump discharge • Brake power if the efficiency is 65%

Q: The surface finish factor for a machine member with sharp circular notch and ultimate strength of…

A: Option B is correct Surface finish factor for a machine member with sharp circular notch is 0.61.

Q: Arm ABCD is pinned at B and undergoes reciprocating motion such that 0 = (0.3 sin 4t) rad, where t…

A: Length BD   Length BA Find the largest speed of A and the acceleration of point D

Q: FMUSC, CUTTING PLANE HORIZONTAL SIEAR FCOMP mg aw "ngL Source Chaffin, D.B., Andersson, G.B,J., and…

A:

Q: Question and needed info below. Thank you in advance

A: The Front view of above given BASE object,

Q: Q222 Describe the methodology for a project report of a workshop, where the pneumatic tools used are…

A: Begin by identifying the pneumatic tools used in the workshop. In this case, the tools are ratchet…

Q: I need help answering questions 1,2, and 3 pertaining to the print attatched below.

A: 1stIn the given drawing there are 4 surface texture symbols.

Q: I Need Help With This SolidWorks Assignment With A Step By Step Process... Quick solution pls 56 88…

A: Open solidworks software and then select new part and set unit system to MMGS. Create a sectional…

Q: Refer to drawing 21A035, what is the depth of the spotface?

A: Spotface: A spotface is an accurate round surface on a machined part providing proper seating of a…

Q: Choose the assumption made for using this FBD.

A: (ii) Answer = (a) explanation = for the FBD of the crate, the assumption that has to be made is that…

Q: how would this look like if written?

A: The feature control frame is required to describe the condition and tolerances of the geometric…

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Q: Consider a hydraulic jack being used in a car repair shop, as in the figure. The pistons have an…

A:

Q: Fill out the table for a .25 basic hole with an LN1 fit Shaft Hole Limits Basic Size Tolerance MMC…

A: Given Data:

Q: ead intrustions on example and help anwser it please and th

A: Jsolid Cylinder =πd432 DAC = 0.9 JAC =π 0.9432=0.064412467

Q: How are you getting 16 mm at the end for an answer  , "HX83=219X10^3/164.909".................is…

A: Stress, σ = FA F = 219 kNσ = 164909 kPa Substituting the values 164.909=219AA = 0.001132 m2 One…

Q: Seems incorrect setup, can you resolve?

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.