Three pipes of diameters 300 mm, 200 mm and 300 mm and lengths 450 m, 255 m and 315 m respectively are connected in series. The difference in water surface levels in two tanks is H. i. Determine the rate of flow of water if the pipes are riveted steel pipes. Consider the minor losses and the major loss. (What is common between pipes 1 and 3?) ii. Draw the Energy grade line. A Н В 3 D1, L1, f¡ Educator D, L, f2 D, L3, f;

Three pipes of diameters 300 mm, 200 mm and 300 mm and lengths 450 m, 255 m and 315 m respectively are connected in series. The difference in water surface levels in two tanks is H. i. Determine the rate of flow of water if the pipes are riveted steel pipes. Consider the minor losses and the major loss. (What is common between pipes 1 and 3?) ii. Draw the Energy grade line. A Н В 3 D1, L1, f¡ Educator D, L, f2 D, L3, f;

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The water needs of a small farm are to be met by pumping water from a well that can supply water continuously at a rate of 50 L/min. The water level in the well is 13 m below the ground level, and water is to be pumped to the farm by a 2-cm internal diameter pipe. The required length of piping is measured to be 20 m, and the total head loss in the piping system is estimated to be 10 m.a) Using Bernoulli equation, determine the pressure difference between the two points (A & B).
Q5: For the system shown in figure. Find the total head loss from (A) to (B). the pipe characteristics are as follows: (Take the flow rate equals 0.6m³/sec) and (u = 10-6 m²/sec). %3D Pipe 1 L(m) 900 D(mm) 600 e or for CH.w. e 0.25mm 300 f 0.03 f = 0.02 CHW. 130 2 1500 3 1000 400 4 1500 750 Flow A
1. To model power production in a traditional hydroelectricity unit, we can use the below schematic figure. Water (e= 998 kg/m3, µ = 0.001 kg/m.s) flows from a large tank at elevation 60 m through a cast iron pipe with total length of L diameter 0.1 m. There are three losses associated with sharp-edge entrance, 90° reg- ular elbow and an open globe valve. Outlet of the valve is discharged to atmosphere. The velocity of the water in the pipe is 3 m/s. For minor losses use values for a flanged pipe with diameter of 4". Find the power produced in the turbine in kW 100 m and unit. Hint: If we write energy grade equation between point 1 (surface of water in tank) and point 2 (left hand side of the valve);" P V P V + 21 – hturbine - Ahtot 2g + 2 pg pg 2g where, P = P2 = Patm and Vi 0 (large tank) Sharp-odge entrance 60 m Elbow Turbine Ginhe Valhe
None
last three digits of My ID number for the length (L) of the pipe in meter is (754)
A pipe is used for energy transmission. Length and diameter of pipe are 80 m and 45 cm respectively. Flow rate is 105 lit/s. Calculate friction loss. Neglect minor losses. Take f = 0.03 .
A water distribution system is supplied from a water reservoir with a bent pipe as shown in the figure. The pipe friction factor f is 0.024. Ignoring all minor losses, the Velocity in the pipe is. d = 100 mm 25 m O a. 11.4 m/s а. O b. 15 m/s 150 m Ос. 3.4 m/s O d. 2.14 m/s
The smooth pipes used in the pumping system in the figure below have a diameter of 150 mm. and its total length is 80 m. In this system; There are four bends with a loss coefficient of 0.2. Lost coefficients; 0.5 for the inlet to the pipe, 0.7 for the valve and 1 for the entrance to the tank. z2-z1 = 15 m above If the flow rate of the water pumped to the tank is 50 L / s and the overall efficiency of the pump is 84%, the manometric discharge Find its height and strength. Take the viscosity of water as 0.001 kg / m.s.
Only a&b