2. DETERMINE THE DISCHARGE THROUGH THREE NEW CAST IRON PIPES, HAVING THE DIAMETERS AS SHOWN IN THE FIGURE. THE TOTAL FRICTIONAL LOSS , EXCLUDING MINOR LOSSES, IS 5 J/N. USE •n = 0.011 FOR ALL PIPES. 600 m 400 m 300 m 15 cm ¢ 20 cm o 25 cm

Q: how did you find humidity ratio

A:

Q: Example of how to size a globe valv

A: A globe valve is a type of valve that has a moveable plug or disc element and a stationary ring…

Q: Multicylinder pump

A: Where more than one cylinder is being driven by one driver, the arrangement is named according to…

Q: Problem 109. Show that the expressions v = rw and ar = ra hold for the motion of the center O of the…

A:

Q: What is the contamination level of a hydraulic fluid with a range code of 18/15?

A: Controlling contamination is the most important task to ensure the reliability of the hydraulic…

Q: Capillary raise occurs due to __________   force of its molecule of the fluid.

A: The capillary rise occurs due to the adhesion force of its molecule of the fluid.   There are two…

Q: Describe the process of Feedforward Regulation system?

A: In feedforward regulation system controller identifies the errors within the system before output…

Q: What is the waterline

A: Solution:   The correct answer with necessary explanation is given below:

Q: 1-While refilling an 8-quart (7.57 L) system with coolant: Technician A initially puts in 4 quarts…

A: Hi there, Thank you for the question. We’ll answer the first question since we answer only one…

Q: Write the monthly maintenance schedule or chart for compressor propeller

A:

Q: Water is flowing thru the pipe set-up. What can be the v thru pipe 3 ?

A:

Q: hat is formula for friction factor?

A: Friction factor: This is also called the Darcy friction factor. It is used in the Darcy-Weisbach…

Q: What is high pressure pump?

A: High-pressure pumps generate a very high pressure of fluid supply. Generally, high-pressure pumps…

Q: Discuss the primary difference between positive displacement pump and dynamic pump. Give example for…

A:

Q: Discuss drying and milling machineries

A: Drying milling machinery’s  Milling machine

Q: What volume of oil to the cylinder is required to cause the cylinder to advance at a speed of 392…

A: Given Data: The speed of advance of the cylinder is, C=392 in/min. The diameter of the piston is,…

Q: List any four factors that are to be considered in selection of storage tanks?

A: The factors are listed below:

Q: The main purpose for hydraulic fluids is:

A: The main purpose for hydraulic fluids is:  1) To transfer the energy from input point to output…

Q: Moving main parts

A: This is a Yanmar 12AY Series Propulsion engine (High speed) with specification of No. of Cylinder 12…

Q: What is value of specific gravity

A: Specific gravity is the ratio of the density of substance with respect to the water .

Q: Explain viscosity in detail of the starting to essy way

A: INTRODUCTION :  A Fluid is a substance that continually flows when an external force is applied.…

Q: Discuss the FRACTIONATING COLUMN in Oil Refinery Plant

A: To Explain : The fractionating column in oil refinery plant.

Q: Describe the PRESSURE MEASUREMENT DEVICES?

A: Pressure measuring devices are used to measure the pressure in a different manner. Based on its…

Q: What is Extensometer?

A: The extensometer is the measuring device that measures the change in length of the object. It is…

Q: What areas within a vane pump or motor are the most susceptible to contamination-induced clearance…

A: Vane Pump :  A vane pump is a type of positive displacement pump that delivers a constant flow rate…

Q: How is done evaluation of whether the improvement is useful and which side of the pipe should be…

A: In order to choose the best strategy, it is necessary to weigh a number of aspects while assessing…

Q: Which of the following statements pertaining to the steel tubing is not true: Steel tubes are…

A: Given: Steel tubes are better than steel pipes because, they:   are less expensive.…

Q: The wall thickness of a pipe is referred to as the pipe's __________.

A: Thickness of the pipe is nothing but the difference between outer radius and inner radius.

Q: 1.5 must be used. Pulley diameters are 9.75in, and tum 1750rpm. Compute fc e following: Design Power…

A:

Q: 100 KH 20 KN/m B 2m C am RI

A:

Q: Define Viscosity

A:

Q: Capsule is used for measuring flow rate. a. False b. True

A: Capsule is used for measuring flow rate. Answer: a) False

Q: Smm 35 MPa

A: Given data; Assume;    A uniform plate containing a rivet hole subjected to uniform       uniaxial…

Q: HOW TO CALCULATE PUMP SIZE

A:

Q: Introduction to pneumatics

A: Pneumatics: It is the branch of science and technology of pressurized air—using piped, compressed…

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.