Mechanical Engineering Question

Q: Cad drawing and assembly drawing of a trolley jack

A: A trolley jack, also known as a floor jack or hydraulic jack, is a mechanical device used to lift…

Q: Q/Draw S and B-M D 8 kuim

A:

Q: For a pump designation 1-x3-10 provided by the manufacture, find out the appropriate options for…

A:

Q: What is the V and M diagram? Thank you!

A:

Q: S e-2"cos t dt = 3 %3D 4 COS

A: Given: ∫0∞e-2tcos2dt=34 The expression for the left-hand side of the question is given by,…

Q: 2. A four-stroke reciprocating engine have a 2000 indicated horsepower. What would be the indicated…

A:

Q: Write short note on compression ratio

A: compression ratio

Q: a) Find the overall efficiency of the system shown below as a function of the two individual…

A: To Find : a) The overall efficiency of the system.Given : The Higher temperature is The…

Q: Given the hook-up drawing, list all the equipment, tools and materials that are needed in…

A:

Q: mf- 10 - SG lo00*t SG:0-82 t= 1o cc (locm?) inf =?

A: The value of m˙f is m˙f=10×SG1000×t=10×0.821000×10=8.2×10-4 cm-3

Q: For the process shown in the schematic below, which of the statements is/are incorrect? Feed hopper…

A: There are two schematic diagrams,the first diagram is the injection moldingsecond is the extrusion…

Q: Q4: A/Compare between single package and split type

A: Comparision between single package and split type

Q: Scale board

A:

Q: What is the total volume, in cubic inches, for bax fill calculations using two internal clamps, six…

A: Given data   Components are : Two internal clamps six THWN copper conductors two single pole…

Q: why bare pipe has 0% efficiency and full covered insulate pipe has more efficiency

A: A thermal insulator has a low thermal conductivity and is a poor heat conductor. To reduce heat loss…

Q: What best describes this print? * A. Casting B. Forging C. Welding D. Machining 2.  There are GD&T…

A: First of all, In the given Engineering drawing the Rotor assembly is given and its parts are drawn…

Q: Explain this diagram

A: Given:To find:Explain the diagram.

Q: Draw the Ts diagram of the whole process

A:

Q: machine design 1 question welding check the seam safety Example= Vd. ME Given data

A: For the given material specification, the yield and tensile stress.

Q: ons: In what situations would a circuit with multiple system pressu Are there any disadvantages to a…

A: 3. Hydraulic pressure is expressed as a force per unit of area, such as bar (kg/cm2) or PSI…

Q: 4 mefeor is aout l a gang and is velocity is 4epined by ve t-5, whare is in seconds. Find fre

A:

Q: ch Liner (ID 6.270

A:

Q: Please all solve the problem

A:

Q: metaicfhread: Pitch- 3mm thocadaryle=65 using 3-wire meltad Best size wisre diametoe ?

A:

Q: Consider a two-stage cascade refrigeration system operating between the pressure limits of 1.2 MPa…

A:

Q: 3.A ball is torsed at s0 m/s at an k the maximum range of the ball and lhcight if the ball was…

A:

Q: Define Constant Specific Heats (Approximate Analysis)

A: In constant specific heat assumption, the specific heat is assumed to be constant at some average…

Q: What is the maximum gas flow rate for a nozzle size?

A: GIVEN; What is the maximum gas flow rate for a nozzle size?

Q: weight vs spring different point plz

A: Weight is a force and spring is a mechanical element. The spring may be compressed or elongates but…

Q: Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and…

A: Volume for each action:Cyl. A extends DE = 65 cubic inCyl. A retracts DR = 62 cubic inCyl. B extends…

Q: Q4 After losing a race championship with few points, a constructor was eager to boost their vehicle…

A: In IC engines a carburetor's function is to air and fuel to supply to the engine. Its primary…

Q: Diagram: Given the hook-up drawing, list all the equipment, tools and materials that are needed in…

A:

Q: What is the area of a rectangular air supply opening measuring 12x10?

A: Given data  Side of a rectangular = 12 × 10 Find the area of rectangular Use  Area = length × width…

Q: Which hotspot on the lever below acts as the Effort?

A: This question is based on the concept of lever.

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: The term, Orthogonal, describes the relationship of the axis of the ½” NPT pipe plug with the main…

Q: what is the changing of diammeter of piping

A: Different pipe fittings are used in the piping networks to achieve transverse, bends, branches, and…

Q: 1a) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 43 mm and…

A:

Q: Do number 13.12

A: Given Data Qr=24000 BTU/hr EER=11 Cost= 14 cents per kWh

Q: Define fluied

A: A fluid is that state of matter which includes both gases and liquids.

Q: 6-a toy sparechúp is attached by asiring ts a ceiling fan and a the fan atatas the spiceship trauefs…

A:

Q: What would an isometric of the oxygen piping system below look like, where PSA GEN = Pressure Swing…

A: can outline a general arrangement for the piping system:PSA GEN (Pressure Swing Adsorption Oxygen…

Q: What company specification number is given to the material for this part?  2. What is the revision…

A: Engg drawing is a technical drawing that is used to transfer the information from the design to the…

Q: The effective capacity is usually higher than design capacity Select one: O True O False

A: As per given question  The effective capacity is usually higher than design capacity Select one